Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wavin-Labko EuroPEK Filter
Summary of Contents for Wavin-Labko EuroPEK Filter
- Page 1 WAVIN-LABKO LTD Labkotie 1 FIN-36240 KANGASALA Tel: +358 20 1285 270 Fax: +358 20 1285 280 24BI01ae www.wavin- labko.fi 02/04 E- mail: tanks@wavin- labko.fi EuroPEK Filter Oil Separator Instructions for Installation, Operation and Maintenance...
-
Page 2: Table Of Contents
EuroPEK Filter - Oil Separator 24BI01ae Contents GENERAL....................................3 ................................3 ESIGN PARAMETERS ...................3 MPORTANT WHEN HANDLING AND INSTALLING THE SEPARATOR TECHNICAL DATA.................................3 ....................................3 PERATION ................................4 YSTEM COMPONENTS ...................................4 CCESSORIES 2.3.1 Anchoring belts................................4 2.3.2 Maintenance shaft................................5 2.3.3 Cast iron cover and frame ............................5 2.3.4... -
Page 3: General
TECHNICAL DATA Operation EuroPEK Filter is designed for processing rain waters from open areas. In the oil separator EuroPEK Filter, both the free and partially the mechanically emulsified oils are separated from the waste water. The operation of the oil separator is based on gravitation, the effect of which is intensified by a filter unit. -
Page 4: System Components
EuroPEK Filter - Oil Separator 24BI01ae System components EuroPEK Filter – oil separator Maximum rain water flow A Inlet and outlet sewer, diameter B Bottom/ Inlet sewer mm 1410 1410 1940 1940 1940 1940 1940 1940 1940 C Bottom/ Outlet sewer... -
Page 5: Maintenance Shaft
EuroPEK Filter - Oil Separator 24BI01ae of belts. Instructions for belt dimensioning can be found e.g. on the Wavin-Labko web pages www.wavin- labko.fi. In easy corrosion environments (calcareous or sandy soil, gravel, loamy sand, soil layers above ground water surface which pass air well or relatively well), electroplated zinc coated ratchets can be used to tighten the belts. -
Page 6: Instructions For Mounting In The Ground
EuroPEK Filter - Oil Separator 24BI01ae INSTRUCTIONS FOR MOUNTING IN THE GROUND These instructions for mounting in the ground apply to standardised oil separator systems EuroPEK Filter. Mounting pit and anchoring slab 1. Excavate a soil area of sufficient size for the separator. The edges of the mounting pit should be estimated with 0.5 metres of extra space from the surface of the... -
Page 7: Installing The Separator
EuroPEK Filter - Oil Separator 24BI01ae 1. RST lug T10 2. Anchoring belt 3. Anchoring slab Slab length = tank length Concrete K30-2 Slab width = tank diameter + 200 mm Reinforcement: A500HW T10 #200 Slab thickness = 150 mm Figure 1. - Page 8 EuroPEK Filter - Oil Separator 24BI01ae 5. If the system is to be equipped with a EuroNOK sampling shaft including a shut-off valve, see separate installation instructions for the sampling and shut-off valve shaft EuroNOK as well as the instructions laminated onto the side of the shaft.
- Page 9 EuroPEK Filter - Oil Separator 24BI01ae frame of the maintenance shaft. From the bolt the grounding is led via a connector on the connection box to equipotential ground. 15. Install the frame of the cover and frame assembly on the maintenance shaft. The...
-
Page 10: Maintenance
EuroPEK Filter - Oil Separator 24BI01ae MAINTENANCE Special attention should be given to the maintenance of the oil separator to ensure effective operation throughout the life span of the system. The need for maintenance depends on the location and purpose of the system. If the separator system is used to... -
Page 11: Maintenance Of The Separator Tank
EuroPEK Filter - Oil Separator 24BI01ae washing waters to the separator, but not straight to the outflow connector, or alternately wash the filter in a place where the dirty washing water can be properly taken care of. 5. Assemble the filter and install it back into the separator, making sure it is well in its place.