Cisco Small Business Unmanaged Switch SR2016 Quick Start Manual page 2

Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other
countries. All other trademarks mentioned in this document or Website are the property of their
respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0705R)
© 2008 Cisco Systems, Inc. All rights reserved.
Printed in the USA on recycled paper containing 10% postconsumer waste.
78-18816-01
3 Installation
Perform the steps in this section to install the hardware.
S 1 Make sure all the devices you will connect to the Switch are
TEP
powered off.
S 2 Connect a Category 5 Ethernet network cable to one of the numbered
TEP
ports on the Switch. Connect the other end to a PC or other network
device.
S 3 Repeat step 2 to connect additional devices.
TEP
S TEP 4 If you are using a mini-GBIC port, connect a mini-GBIC module to the
port. For detailed instructions, refer to the module's documentation.
N OTE The mini-GBIC ports are shared. Do not use port 12 if you
are using themini-GBIC1 port. Do not use port 24 if you are
using the mini-GBIC2 port.
S TEP 5 Connect the supplied power cord to the Switch's power port, and plug
the other end into an electrical outlet. When connecting power, always
use a surge protector.
S TEP 6 Power on the devices connected to the Switch. Each active port's
corresponding LED will light up on the Switch.
Congratulations! The installation of the 10/100/1000 Gigabit Switch is
complete!
4 Specifications
The following table lists the specifications for the SR2016 10/100/1000 Gigabit
Switch.
Model SR2016
Standards IEEE 802.3, 802.3u, 802.3x,
802.3ab
Ports 16 10/100/1000 Mbps RJ-45
ports
Cabling Type Cat5 Ethernet
LEDs System, 1 through 16
Dimensions WxHxD
10.98" x 1.75" x 9.45"
279 mm x 44.5 mm x 240 mm
Unit Weight 4.75 lbs (2. 1 55 kg)
Power 110-120VAC, 100W
Certification FCC Class A, CE
Operating Temperature 32 to 104ºF (0 to 40ºC)
Storage Temperature -40 to 158ºF (-40 to 70ºC)
Operating Humidy 20% to 95%, noncondensing
Storage Humidy 5% to 95%, noncondensing
The following table lists the specifications for the SR2024C 10/100/1000
Gigabit Switch.
Model SR2024C
Standards IEEE 802.3, 802.3u, 802.3x,
802.3ab
Ports 24 10/100/1000 Mbps RJ-45
ports + 2 mini-GBIC ports
Cabling Type Cat5 Ethernet
LEDs System, 1 through 24
Dimensions WxHxD
17.00" x 1.75" x 13.74"
432 mm x 44.5 mm x 349 mm
Unit Weight 7.98 lbs (3.621 kg)
Power 100-127/200-240V~1.0A/0.5A
50~60HZ
Certification FCC Class A, CE
Operating Temperature 32 to 104ºF (0 to 40ºC)
Storage Temperature -4 to 158ºF (-20 to 70ºC)
Operating Humidity 10% to 90%, noncondensing
Storage Humidity 10% to 95%, noncondensing
5 Where to Go From Here
Resource Location
Customer Support www.cisco.com/go/smallbiz
End User License Agreement www.cisco.com/go/smallbiz
Regulatory Compliance and Safety www.cisco.com/go/smallbiz
Information
Warranty Information www.cisco.com/go/smallbiz
Cisco Partner Central site for Small www.cisco.com/web/partners/sell/
Business smb/