Advertisement
06
How do I...
Display room temperature
Press
or
once.
Increase room temperature
Press
for 3 seconds until display starts to flash. T his
brings you into target temperature edit mode. Press
until desired target te mperature is obtained.
Decrease room temperature
Press
for 3 se conds until target temperature st arts to
flash. It will show the c urrent target. Press
target temperature is obtained.
Boost
If no s chedule or boost is running, press
seconds. The bo ost target will be set to 20°C or 2°C above
the current room temperature if already above 20°C .
Setup schedules
Log-on t o heatboss
user interface. Navigate to the
®
desired ro om and click
. From here you can create,
modify or delete schedules.
Reset
To reset the therm ostat press and hold
buttons simultaneously for 10 se conds. The display will
flash the target temperature. W hen
device displays th e sy mbol to the right
release both buttons . The thermostat
will now start to sync to hub.
Power mode
If your thermostat is powered from the
mains by the P ower Module it will display
the s ymbol to the right upon startup. In this
mode the relays in the thermostat Power
Module are controlled.
If your thermostat is po wered by battery it
will display the icon to the right upon startup.
In this mode the relays are not controlled
and the motion sensor is disab led.
07
heatboss® thermostat power module
until desired
This is used to power the heatboss® stat and allows the
stat to control external s ystems such as zone valves. It
contains two relays R
for 3
heating and c ooling respectively. There is a common
header input that will be s witched by the relays. The
common header is voltage free.
and
How to install thermostat power module
•
Ensure module is placed the
correct way up, then fix onto the
back of the bac kplate with the
two screws provided.
•
Wire in power 240V A C (L = live, N = neutral)
•
If the relays are going to be used to control/signal
ext ernal equipment wire these now. The 'C ' (voltage free)
common will be sw itched by R
•
Ensure wires are not exerting any force on any of the
components of the P C B .
•
Scre w the back plate to the s ocke t.
and R
which are c ontrolled for
1
2
Live
240V~
Neutral
C
R
SW
2
R
2
1
SW
1
Stat Power
Backplate
Module
and R
.
1
2
08
Therm ostat Ty pe
Intelligent Electronic
S oftware Cl ass ificat ion
Sa fety Cl ass ificat ion
Battery Lif e
P ow er S ourc e
2x 1 .5V Lithium AA / P ower Module
Measurement I nterva l
Co ntr ol A ccur ac y (tem p. / R H)
Scann ing T em perature Ran ge
Tem peratur e Co ntr ol R an ge
S ize
L: 95mm Ø: 8 5mm
We ight
IP Cl as s
II Co mpletely protected by its enclosure
2.4Ghz mesh Zigbee
Radio Signal
P ow er Mod ule T echn ica l S pec ificat ion
T ype
Use for heatboss® st at only
Sa fety Cl ass ificat ion
S ize
Mechan ica l Co ntac t
Re lay S witch M ax
Re lay Voltage S witche d
Voltage free via C pin header
Safety Precautions
The heatboss
stat should not be used in places where
®
it can be expos ed to water.
Unit 1, F arranshane H ouse
1 B allygore Ro ad
Antrim
+44(0)28 9422 8141
C o. Antrim
info@heatboss. co.uk
Northern Ireland
www.heatboss .co.uk
B T41 2R N
Wireless Stat
C lass A
C lass II
Up to 1.5 years
Every minute
+/- 1°C / +/- 5%
-9°C to 45° C
-9°C to 45° C
113g
C lass I I
65mm x 65mm
Re lay
5v
Advertisement
