Advertisement
Quick Links
Advertisement
Related Manuals for 2M Technology 2MTHWT-HMD-II
Summary of Contents for 2M Technology 2MTHWT-HMD-II
- Page 1 DIGITAL DETECTION MODULE Quick Guide Version: 1.01 REV06122020...
-
Page 2: Packing List
Digital Detection Module - Quick Guide Packing List Name Unit Digital detection module Screw kit (two M3x6 countersunk head screws and two M3x6 pan head screws inside) Power adapter (purchased separately) Bracket Hint label Special statement User manual Product Overview The digital detection module is a non-contact device for taking wrist temperatures. - Page 3 Digital Detection Module - Quick Guide Overvoltage category (except cord/plug-connected equipment): Ⅱ Pollution degree of the intended environment: the operational environment should be with less dust to avoid the pollution of blackbody target. (Pollution degree 2) If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
-
Page 4: Device Installation
Digital Detection Module - Quick Guide Device Installation Device Wiring 1 Wiring Embedding Before installing the digital detection module, plan the layout of the power cable. For the diameter selection for the extension power cable, see the table below. Diameter Selection for Extension Power Cables The device is powered by DC 12V/2A and the lower limit of the operating voltage is DC 9V (12V–25%). - Page 5 Digital Detection Module - Quick Guide Tools Preparations Antistatic wrist strap or antistatic gloves Marker Drill M8/M6 simple open-end wrench Phillips screwdriver Slotted screwdriver Installation Steps NOTE! Before installing the digital detection module, connect the cables between the module and a face recognition access control terminal/face recognition terminal by referring to section "Device Wiring"...
- Page 6 Digital Detection Module - Quick Guide Installation mode 2 2. Fix the side- mounted bracket. 1. Fix the wall- mounted bracket. 3. Fix the temperature measurement module. NOTE! This installation mode requires the 2WTK-SZWB bracket, which needs to be purchased separately.
-
Page 7: Device Startup
Digital Detection Module - Quick Guide Device Startup 1 Device power-on After the device is installed correctly, connect the power adapter (provided separately) to the mains supply to start the device. 2 Device configuration Local configuration When the digital detection module is used in combination with a face recognition access control terminal, you can enable the temperature measurement function on the Authentication Scene interface of the face recognition access control terminal. - Page 8 Digital Detection Module - Quick Guide Configuration on the Web interface You can also log in to the Web interface of the terminal and choose Setup > Intelligent > Advanced Setting to enable the temperature measurement function. 3 Device operations When the temperature needs to be measured, aim the wrist at the temperature measurement point, at a distance of 0.39–1”...
- Page 9 Digital Detection Module - Quick Guide Label Attaching The packing list contains temperature measurement hint labels, which directly tell users the temperature measurement point and distance. After installing the device, attach the label to a proper position of the temperature measurement module. (0.39”- 1”...
- Page 10 Digital Detection Module - Quick Guide FAQs Failure/Symptom Solution What should I do if 1. Check whether the measurement distance is proper. The some people's recommended measurement distance is 0.39”-1”. temperatures 2. Check whether the wrist is aimed at the temperature cannot be taken? measurement point.
- Page 11 Digital Detection Module - Quick Guide Failure/Symptom Solution What should I do 1. Check whether a person has behaviors that affect the when a high body temperature, for example, getting out of a hot car, temperature alarm doing strenuous exercise, or carrying hot drinks and hot is reported during food.
- Page 12 Digital Detection Module - Quick Guide Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
- Page 13 Digital Detection Module - Quick Guide Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attack, hacking, and virus. We strongly recommends that users take all necessary measures to enhance the protection of network, device, data and personal information.
- Page 14 Digital Detection Module - Quick Guide Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions. Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and the system will automatically forward port data, which results in the risks of data leakage.
- Page 15 Digital Detection Module - Quick Guide Use a mains socket outlet with a protective earthing (grounding) connection. Ground your device properly if the device is intended to be grounded. Battery Use Caution When battery is used, avoid: ...
- Page 16 Digital Detection Module - Quick Guide This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU. WEEE Directive–2012/19/EU The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.
- Page 17 802 Greenview Dr. Grand Prairie TX. 75050 USA Toll Free: 1-866-708-5401 Fax: (+1) 972-999-4113 sales@2MTechnology.net...