Special Mode Setting Button - Marantz SR7013 Service Manual

SPECIAL MODE

Special mode setting button

b No. 1 - 4, 6 - 8 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power.
b No. 5, 9, 10 : While the power is on, hold down buttons "A", "B", and "C" for at least 3 seconds .
No. Mode
Version Display Mode
1
(u-COM / DSP Error Display)
PANEL / REMOTE LOCK Selection
2
Mode
3 Selecting the Mode for Service-related
3-1 Check the Video/Audio path Mode
3-2 Protection history display mode
3-3 232C Standby Clear Mode
3-4 Operation Info Mode
TUNER STEP Mode
3-5
(U and N model only)
4 Protection Pass Mode
5 Network Initialization Mode
6 User Initialization Mode
7 Factory Initialization Mode
8 Clearing the Operation Info
9 HDMI Diagnostics Mode
10 Log Capture feature
NOTE : If the two indicator lights at the bottom right of the FLD display "
To release this special mode, press and hold the "DIMMER" and "STATUS" buttons for 3 seconds or more while the power is ON. The RS-232C communication is available when the two indicator lights at the
bottom right of the FLD go out.
Button A Button B Button C
Displays the version of firmware such as the main firmware or DSP. Errors that have occurred are displayed.
DIMMER STATUS -
(See 1. Version Display
Start this unit in the PANEL/REMOTE LOCK selection mode so that PANEL LOCK and Remote Lock can be switched between On and
Off. (See 2. PANEL / REMOTE LOCK Selection
·PANEL LOCK Mode (with Volume)
Disables reception from all keys and encoders on the front panel except the power button (including the volume).
BACK ENTER -
·PANEL LOCK Mode (without Volume)
Disables reception from all keys and encoders on the front panel except the power button and volume encoder.
·PANEL LOCK mode is turned off
This is a display for turning on each service-related mode.
ZONE
BACK -
SELECT Service-related modes:No. 3-1 - No. 3-5
This is a special mode for service confirmation used during repair work to simplify the confirmation work for the Audio channel /
↑ ↑ -
video channel. (See
Displays the protection occurrence history. (See
↑ ↑ -
Switches from 232C standby mode to normal standby mode. (See
↑ ↑ -
Displays the accumulated operating time of the unit, the number of times the power was switched on, and the number of occur-
↑ ↑ -
rences of each protection. (See
Enables reception STEP of the ANALOG TUNER to be changed.
↑ ↑ -
(See 3-5. TUNER STEP mode (U / N
Enables the power to be turned on when protection detection is disabled.
DYNAMIC DYNAMIC
M-DAX
EQ VOL (See 4. Protection Pass
Network module backup data is initialized. (See
BACK ENTER -
Initialize the backup data for the MCU and network module. (Settings for the Installer Setup are not initialized.)
GAME INFO -
Initialize the backup data only for MCU.
MOVIE MUSIC -
(Settings for the Installer Setup are initialized) (Network function settings are not initialized.) (See
Clear the accumulated operating time of the unit, the number of times the power was switched on, and the number of occurrences
DYNAMIC DYNAMIC
-
EQ VOL of each protection. (See
This mode is used to identify and solve the cause when there is a connectivity issue with this unit and an HDMI device.
BACK CURSOR d
For details on the operating methods and diagnosis procedures, see the HDMI Diagnostics and Troubleshooting guide issued on SDI.
Acquires the Network Module log. The log is deleted when the Network Module is deleted. (See
MOVIE INFO -
", this means that the unit has entered the special developer's mode. In this case, the RS-232C communication is not available.
M-DAX
DYNAMIC EQ
indicator Lights
X
MOVIE
Mode)
Mode)
Service Path Check Mode)
3-2. Protection History Display
3-4. Operation Info Mode)
only))
Mode)
5. Network Initialization
6. Clearing the Operation Info)
DYNAMIC VOL BACK CURSOR d
ENTER
GAME DIMMER ZONE SELECT
MUSIC INFO STATUS
148
Descriptions
Mode)
3-3. 232C Standby Clear Mode)
Mode)
Initializing this
7. Log Capture
Unit)
feature)