Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Sunerg Solar Energy XMCH66400BW+H
Summary of Contents for Sunerg Solar Energy XMCH66400BW+H
- Page 1 Single glass crystalline silicon PV Modules installation manual Rev.1_2022...
- Page 3 Any questions, please contact with the salesman or customer service personnel of Sunerg Solar for further explanations. 2.2 Applicable products This manual is intended for use with the following solar modules: （ Horizontal ） Monocrystalline PERC PV modules : XMCH66400BW+H; XMCH120400B+H; XMCH120410BW+H...
- Page 4 Module dimensions and electrical performance data are details in the corresponding technical specifications. 3 Product information Section structure and component description of PV modules 1、Frame 2、Glass 3、EVA 4、Solar Cell 5、Backsheet 6、Adhesive 7、Junction box 8、Cable 9、Connector 10、Lable 11、Ground hole 12、Mounting hole 13、Drainage hole 14、Stiffener Figure 1 Section structure and module description...
- Page 5 open circuit voltage, short circuit current, maximum system voltage, PV module size and weight under standard test conditions. Series number: Each module has a unique bar code number, each bar code number has 20 letters and numbers. The bar code is permanently encapsulated inside the module, as can be seen clearly from the top right corner of the module.
- Page 6 modules directly to sunlight for a long time. 4.2.5 Do not change the configuration of the bypass diodes. Do not disassemble the modules. 4.2.6 Do not contact with module surface when the module is wet unless to clean the modules, please following requirements mentioned in this manual when cleaning.
- Page 7 4.4.8 During modules interconnection, ensure to fix the connecting cables to supporting bracket, so as to restrict the swing amplitude of the slack part of the cables. 4.4.9 Abide by the allowable minimum bending radius of the cables (suggest no less than 43mm). 4.4.10 Always protect the cable with conduit where animals or children can touch it.
- Page 8 such as the seaside, farm, high humidity or wind and other large environment, please consult your local dealer for professional support and confirmation. If you need to be installed at a high altitude, the altitude should not exceed 2000m. 5.2.5 PV modules have passed IEC61701 salt-mist, but galvanic corrosion can occur between the aluminum frame of the modules and mounting or grounding hardware is comprised of dissimilar metals.
- Page 9 the guarantee. The installation supporting rail must be tested by the third-party organization with the analysis ability of Static Mechanical according to the local national or international standards. 6.1.2 The supporting rail must be made of environmental corrosion, anti-rust and UV-resistant materials. 6.1.3 Modules must be securely fastened to the supporting rail.
- Page 10 Figure 3 Schematic diagram of reinforcement mounting of module 6.2.2 Pole mounting When installing a module on a pole, choose a pole and supporting rail that will withstand the anticipated wind power of the local area. The pole must be constructed on a solid foundation. 6.2.3 Ground mounting Select the height of the mounting system to prevent the lowest edge of the module from being covered by snow for a long time in winter in areas with heavy snowfalls.
- Page 11 Spring Stainless steel washer Flat washer Stainless steel Stainless steel 6.3.3 Fixture installation 6.3.3.1 Use a certain number of clamps to fix the modules on the mounting bracket. Sunerg recommends that the clamps be clamped on the long frame of the module. The area of the A side of the module frame held by each fixed clamp is not less than 400mm2 (clamp length: ≥50mm, The width of the contact between the fixture and the A surface of the frame: 9～11mm).
- Page 12 Fixture A: Fixture for edge module Fixture B: Fixture for intermediate modules For the 30 frame, the recommended value of X is 29mm For the 30 frame, the recommended value of Y is 20mm For the frame, the recommended value of X is 34mm For the frame, the recommended value of Y is 25mm For the...
- Page 13 (a) Take care of the module frames, not to twist or deform them. (b) Avoid the clamps’ shading influence the module. (c) Not to damage the surface of module frame. (d) Make sure that the module's drainage holes not be plugged. Installation Module Type mechanical load /Pa...
- Page 14 1000mm. Vertical Installation （Double row） The wire length of 72 / 78 is not less than 700mm, and each string needs to add a jumper wire not less than 900mm. The wire length of 60 / 66 is not less than 700mm, and each string needs to add a jumper wire not less than 500mm.
- Page 15 Head to tail connection The wire length of this connection mode is not less than 800mm. During installation, attention should be paid to the positive and negative pole positions of the modules, and the next module need to be turned around . The wire length of this connection mode is not less than 1400mm.
- Page 16 current and voltage than reported at standard test conditions. Accordingly, the values of ISC and VOC marked on this module should be multiplied by a factor of 1.25 when determining module voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. 7.1.2 Try to use the modules with the same configuration in the same PV system.
- Page 17 7.3.1 When connecting modules, make sure that the connectors of the same series module shall come from the same manufacturer or totally be compatible with each others, and the same requirements shall go to the connection terminals of series string and PV system, because the connectors from different manufacturers may not be compatible with each others, which easily leads to mismatch risk.
- Page 18 with M4 nuts. Spring washers should be used to prevent the screws from loosening and lead to poor grounding. 7.5.6 If the module is used in high-temperature and high-humidity environment, Sunerg Solar suggest the customer configure the inverter which allows negative grounding and contains isolation transformer (as shown in figure 7).
- Page 19 Please carefully check the modules of the existence of visual defects, focusing on the following items: Check whether the module glass is broken. Check if the front of the module is obstructed by obstacles or foreign objects. Check the module negative-sheet whether there is hot, negative film raised, burn through the traces and so on.
Need help?
Do you have a question about the XMCH66400BW+H and is the answer not in the manual?
Questions and answers