Table of Contents
Advertisement
7.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
7.6 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
The fan run-on removes remaining odours and is used
to dry the odour filter after the cooking process.
Press
repeatedly until the fan run-on is switched
▶
on.
a LED 1 for the fan setting lights up in the LED dis-
play. LED 6 flashes for the fan run-on.
a The appliance switches off automatically after ap-
prox. 10 minutes.
7.7 Switching off the fan run-on
Press
.
▶
a This temporarily stops the fan run-on.
7.8 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press
.
▶
a In the LED display, LED 6 lights up for automatic
mode.
7.9 Switch off automatic mode
Press
.
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
7.10 Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note: This function is only available in the Home Con-
nect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
7.11 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Default setting: Fan setting 3
1
Depending on the appliance specifications
1
1
1
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
.
7.12 Setting the sensor control
Requirement: The appliance is switched off.
Press and hold
1.
Press
2.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. 3 seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.13 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡ A signal sounds repeatedly.
Press
▶
a The saturation indicator is reset.
7.14 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold
1.
To set circulating-air mode (non-regenerable fil-
‒
ter), press
display.
To set circulating-air mode (non-regenerable fil-
‒
ter), press
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
2.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press .
a A signal tone sounds as soon as the selected set-
ting is saved.
7.15 Switching on the lighting
Press to switch on the lighting.
▶
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
7.16 Switching off the lighting
Switch off the lighting with
▶
and
for approx. 3 seconds.
or to change the setting.
.
and
for approx. three seconds.
/ until LED 2 lights up in the LED
/ until LED 3 lights up in the LED
.
Basic operation en
1
and for ap-
/
7
Advertisement
Table of Contents
