Summary of Contents for In-Ex 165
- Page 1 OWNER’S MANUAL FOR THE Spreader 165 In-Ex™ P O Box 1010, 145 Harts Road Palmerston North Ph: 06 354 6060 Fax: 06 355 3199 E-Mail: sales@c-dax.co.nz...
-
Page 2: Safety Precautions
YOUR SAFETY IS In-Ex’s PRIMARY CONCERN ▪ It is important that you understand that any loads or attachments whether fastened to or placed on a vehicle or ATV will alter the stability and handling characteristics of that vehicle or ATV. -
Page 3: Table Of Contents
In-Ex Spreader 165 OWNER’S MANUAL (Pt.No.2400-6945 Issue 8, Aug 2022) TABLE OF CONTENTS Safety Precautions Table of Contents Description Specifications Order Information Warranty Operation Calibration Operating the Spreader Adjusting the Spread Pattern Fitting the Rain Cover Maintenance Before Use After Each Use or Daily when in Use... -
Page 4: Description
DESCRIPTION The In-Ex Spreader 165 is a ground-driven spreader designed for application of pelleted fertilisers. It can also be used for application of other products such as grass seed and magnesium oxide. The uniquely designed 165-litre translucent non-corrosive polyethylene hopper is specially profiled for good product flow and ease of filling. - Page 5 Liability Except for the warranty set out in clause 1.2 above, all warranties and representations (including those expressed or implied by law) in respect of the equipment or advice relating to the equipment provided to you by C-Dax are excluded to the extent permitted by law. Notwithstanding anything else in this manual, C-Dax’s maximum liability to you (in the event that such liability exists) in respect of any breach of warranty, any matter set out in this manual, or for defective equipment or advice relating to the equipment provided is limited at...
-
Page 6: Operation
OPERATION The product to be spread is placed in the hopper. When the spreader is towed forward, the right hand wheel drives through the pin clutch and gearbox to turn the spinner in a clockwise direction. When the shutter handle is pulled forward, the shutter at the bottom of the hopper rotates to an open position. -
Page 7: Operating The Spreader
OPERATING THE SPREADER When the spreader has been correctly calibrated, the hopper may be filled to the required level and spreading commenced. To reduce agitator damage to product and to ensure that product is not forced past the agitator shaft when towing the spreader to the area to be treated, the drive to the gearbox should be disconnected by removing the pin from the drive axle until spreading is to be commenced. -
Page 8: Fitting The Rain Cover
Fitting the Rain Cover The rain cover is permanently fitted via an aluminium bracket mounted on the back of the spreader. To fit the rain cover to the hopper, pull the cover over the top of the spreader and pull the (bungee) cord down over the lugs mounted on the frame. -
Page 9: Parts Diagram
Parts Diagram... -
Page 10: Parts List
Fastener-Washer-Flat-3/16"x1/2"x1.5-Grade 304-Stainless 1 3310-9750 Fastener-Washer-Flat-23.5x2"x1.5-Grade 304-Stainless 1 3500-5305 Frame-Spreader-MM/In-Ex 165L-GL 1 3800-2000 Gearbox-Ferroni-RV12-2-6-Ratio 1 to 3.25 1 3865-3800 Grip-Handle-7/8"-PVC-Black-Plastic 1 4050-8105 Handle-Spreader 165L/Mag 165-ZP 1 5200-6700 Machined-Axle-Gearbox Drive-Magmaster-Black 1 5245-4010 Mount-Hopper Cover-Spreader 130L/165L/Magmaster 165-AL 1 5270-0003 Nipple-Grease-Straight-Short-M6-ZP 1 6100-4820 Pin-Locking-6x50mm-ZP... - Page 11 1 7500-2105 Rota-Hopper-Spreader-165L -Natural-MDPE-In-Ex 1 7500-2795 Rota-Spout-Spreader-165/300/400-Natural-MDPE 1 7970-8020 Shroud-Spreader 165-Natural-MDPE 1 8200-2100 Spinner-Disc-CDIT300/400-GL 1 8200-5305 Spinner-Mount-Spreader 165L/Magmaster 165-ZP 1 8250-1800 Spring-Compression-Crinkle Plate-ZP 1 8800-3800 Tow-Coupling-Handle-Double Ended-1 7/8" x 50mm-ZP 4 8910-8000 Vane-Spinner-Spreader 130L/165L/Magmaster 165-GL 1 9200-8610 Wheel-Turf-DRILLED-DRIVE-18x750x8-Tubeless 1 9200-8600...