Safe Fleet C3W9PD03E Quick Install Manual

Accessing the Camera using a web browser
You can use a web browser to access and configure the camera over the Internet.
For a direct connection to a single camera:
1. Using a Web browser, enter the camera's IP address (default is 172.30.1.1). The Login dialog box appears.
Note: Ensure that the Active X controls are enabled.
2. Enter your user name and password. Default user name is Admin and default password is 11111111.
3. Click Login. The web browser window appears.
If you want to access a camera connected to a PoE Switch (part #: NS18POE16), the IP address of each
cameras varies:
• Channel 1: 172.31.1.101
• Channel 2: 172.31.1.102
• Channel 3: 172.31.1.103, etc.
• Channel 16: 172.31.1.116
Warranty
For full warranty information, visit:
• www.seon.com/documents/Seon-Warranty.pdf
2002/96/EC (WEEE directive): This product cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return the product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated collection points, for more
information, see www.recyclethis.info.
2006/66/EC (battery directive): This product does not contain batteries.
Support
• Phone: 1-844-899-7366
• Email: service@seon.com
C3W9PD
Package Contents
Check the package and contents for visible damage. If
any components are damaged or missing, contact the
Seon Service team and request an RMA (Return Material
Authorization).
Package contents:
• Camera
• Drill Template
• Torx Security Wrench
• Brush Guard
• Weatherproof cap for RJ45 connector
• Qty 4 - #10, 1" Mounting Screws
Cable Requirements
It is recommended that camera harnesses be purchased
directly from Safe Fleet. All network cabling must be
installed according to applicable codes and regulations.
Cable should be CAT5e or CAT6, stranded or solid, 24
AWG or better. Both ends must be terminated with male
RJ45 connectors and should conform to TIA/EIA-568-B
standards. Spliced cables are not acceptable.
Service
If your C3W9PD Camera is to be returned for service, please call toll free 1.877.630.7366, or 1.844.899.7366,
and provide the model and/or serial# of your unit.
Ask for a Return Merchandise Authorization (RMA) number. An RMA# allows the Service Technicians to better
track your product when it comes in for service. Please show the RMA# on the outside of the package. ANY
PRODUCT SENT WITHOUT AN RMA# MAY BE REFUSED.
Documentation
Additional copies of this guide, along with other supporting documentation can be found on the Safe Fleet
Community:
• https://community.seon.com/documents/
Quick Install Guide
For camera models:
C3W9PD03E, C3W9PD03E-G, C3W9PD04E, C3W9PD04E-G
Installation Environment
When installing your product, consider the
following:
• Electrical: Install electrical wiring carefully.
This should be done by qualified service
personnel. Always use a proper PoE
switch to power the camera.
• Ventilation: Ensure that the location
planned for the installation of the camera
is well ventilated.
• Temperature: Do not operate the camera
beyond the specified temperature,
humidity, or power source ratings. The
operating temperature of the camera is
between -40°C and +65°C.
• Servicing: Do not attempt to repair this
camera yourself. Any attempt to dismantle
this product, except as required for normal
installation, will negate the warranty and
may also result in injury. Refer all servicing
to qualified service personnel.
• Cleaning: Do not touch the lens with your
fingers. If cleaning is necessary, use a
clean soft cloth with isopropyl alcohol and
gently wipe the camera.
© Safe Fleet | Mar 2019 | All rights reserved | Part #: 700-1163 R1