Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NODEXON NX-AP8000 Series
Summary of Contents for NODEXON NX-AP8000 Series
- Page 1 NX-AP8000 Outdoor Access Point Switch Series Product Guide...
- Page 2 This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest information through the Nodexon Networks website. Nodexon Networks endeavors to ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.
- Page 3 It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it is assumed that the users are already familiar with the related terms and concepts. Obtaining Technical Assistance Nodexon Networks Website: https://www.nodexonnetworks.com/ Technical Support Website: https://nodexonnetworks.com/support...
-
Page 4: Product Overview
1 Product Overview The NX-AP8000 is a wireless access point (AP) designed by Nodexon for next-generation high-speed wireless LANs. Adhering to the latest 802.11ac standard, the AP delivers an access rate of up to 1.75Gbps. It features security, radio frequency (RF) control, mobile access, Quality of Service (QoS), and seamless roaming. In addition, it can be managed by NX-WS series wireless access controllers (ACs) to implement wireless data forwarding, security, and access control. -
Page 5: Product Appearance
IP68 IP Rating <2.5 kg (5.51 lbs) Weight GB4943, EN60601-1-2 (medical care), UL/CSA 60950-1, EN/IEC 60950-1, EN/IEC 60950-22 Safety Standards GB9254-2008, EN301 489, EN55022, FCC Part15, RSS-210 EMC Standards Table 1-2 LEDs of NX-AP8000 State Meaning Blinking green Initialization in progress Blinking yellow Initialization is complete, but no CAPWAP connection. -
Page 6: Front View
1.3 Front View Figure 1-2 NX-AP8000 Front View 1. 2.4GHz antenna connector 2. Console port 3.10/100/1000 Base-T auto-sensing Ethernet/PoE 4.10/100/1000 Base-T auto-sensing Note: OUT port Ethernet/PoE IN port 5. SFP combo port 6. 5GHz antenna connector For AP630(IDA) and AP630(IODA), the PoE OUT functionality of LAN 2 is supported on hardware versions earlier than V2.1x. -
Page 7: Preparing For Installation
2 Preparing for Installation To prevent device damage and physical injury, please read carefully the safety recommendations described in this chapter. Recommendations do not cover all possible hazardous situations. 2.1 Grounding and Lightning Protection Keep the grounding connection within 30 m, and use a 40 mm x 4 mm or 50 mm x 5 mm ground bar of hot-dip zinc-coated flat steel sheet. -
Page 8: Temperature And Humidity
2.2.1 Temperature and Humidity Table 2-1 Required Temperature and Humidity for the NX-AP8000 Series -40° C to 65° C (-40°F to 149°F) Operating Temperature 0% to 100% (non-condensing) Operating Humidity 2.2.2 Outdoor Installation The AP can be installed outdoors and mounted on a wall or pole. 2.2.3 Waterproof Use a seal plug to seal the unused ports. -
Page 9: Fiber Connection
Radiation interference occurs when energy (usually radio frequency energy) is emitted from a device and propagated through space to disrupt other devices. The interference source can be part of disrupted system or a fully electrically isolated unit. Conduction interference occurs when interference is transferred from one unit to another through cables, which are usually electromagnetic wires or signal cables connected between the source and the device(s) experiencing interference. -
Page 10: Installing The Access Point
· 3 Installing the Access Point Before installing the AP, make sure you have carefully read the requirements described in Chapter 2. 3.1 Installation Flowchart Start Check Choose the Site Install the Bracket on a Pole Install the Bracket on a Wall Install the AP Install External Antenna (Optional) Adjust Antenna Orientation... -
Page 11: Before You Begin
3.2 Before You Begin Before you install the AP, verify that all the parts in the packing list are there and make sure that: The installation site meets temperature and humidity requirements. The installation site is equipped with a proper power supply. ... - Page 12 · Attach the tie rod to the mounting plate and fasten the rod with the M8x40 screws after AP is well-positioned See Figure 3-3. Figure 3-3 Fixing the Tie Rod on the Mounting Plate Wall mount 3) Use the supplied cross-shaped bracket and M8 x 60 expansion anchors to implement the wall mount. Attach the cross-shaped bracket to the wall and mark the screw hole locations.
- Page 13 b. Hang the AP with the AP-side mounting bracket module to the cross-shaped bracket and tighten three M8×40 screws to secure the AP. Finally, drive the screw of Loop B into the fourth anchor. See Figure 3-5. Figure 3-5 Wall Mount ...
-
Page 14: Adjusting Antenna Orientation
Figure 3-7 Installing the AP on a Vertical Pole The procedure of horizontal pole mount is similar as that of a vertical mount. If the diameter of the pole is out of the range, the hose clamp is customer-supplied. In this case, we strongly recommend you to use a 304 stainless steel hose clamp with thickness of 2.5mm at least. - Page 15 Figure 3-9 Clockwise Horizontal Rotation (+60°) 60° (-60°to +60°horizontal rotation available) Figure 3-10 Vertical Rotation (0°) Figure 3-11 Clockwise Vertical Rotation (+60°) (0°to 90° vertical rotation available)
-
Page 16: Connecting Cables
NX-AP8530-5 Antenna Orientation Figure 3-12 Anticlockwise Vertical Rotation (-90°) 3.6 Installing a Security Lock (Optional) The security lock is customer-supplied. The lock loop on the AP is for your security needs. You can fasten the AP to a fixture as follows: Fasten the cable of a security lock to a fixture;... - Page 17 Figure 3-14 Grounding the AP Connecting the network cable Waterproofing material is customer-supplied. Trim the network cable according to the distance between the AP and the power supply. Thread the cable through liquid-tight adapter and add a plug to the end. See figure 3-15. Figure 3-15 Threading the Network Cable Wrap the cable between B and C upwards with two or three layers of liquid-tight material.
-
Page 18: Installing Outdoor Antennas (Optional)
· Thread the fiber through the liquid-tight adapter in the order as shown in figure 3-17. Figure 3-17 Threading the Fiber Insert the plug of the fiber into the SPF port. Tighten A. Combine B and C and put the combination into A. Tighten D before applying waterproof glue to its joint with A. - Page 19 Installing Outdoor Omnidirectional Antennas Omnidirectional antennas must be kept at least one meter away from any metal. Do not weld the lightning rod onto the pole installed with an omni-directional antenna. Place the lightning rod in the middle of two omni-directional antennas.
-
Page 20: Appendix A: Connectors And Media
Appendix A: Connectors and Media 1000BASE-T/100BASE-TX/10BASE-T The 1000BASE-T/100BASE-TX/10BASE-T is a 10/100/1000 Mbps auto-negotiation port that supports auto MDI/MDIX. Compliant with IEEE 802.3ab, 1000BASE-T requires Category 5e 100-ohm UTP or STP (STP is recommended) with a maximum distance of 100 meters (328 feet). 1000BASE-T requires all four pairs of wires be connected for data transmission, as shown in Figure A-1. - Page 21 · Fiber Connection You can choose to use single mode or multimode fibers according to the transceiver module types. Figure A-3 shows connection of fiber cables. Figure A-3 Fiber Connection...
-
Page 22: Appendix B Mini-Gbic Module Specifications
Appendix B Mini-GBIC Module Specifications Nodexon provides various Gigabit SFP transceivers (Mini-GBIC modules) for interfaces of wireless access controllers. You can select the most suitable SFP modules as needed. This appendix describes the models and specifications of some of the Gigabit SFP transceivers for your reference.