Related Manuals for Kane KANE505
Summary of Contents for Kane KANE505
- Page 1 KANE505 ® 1000V Digital Multimeter INSTRUCTION MANUAL ENGLISH ® RANGE MIN/MAX HOLD FAST 600V CAT III 1000V CAT II...
-
Page 2: Table Of Contents
TABLE OF CONTENTS FUNCTIONS ..............................3 FEATURES ..............................3 GENERAL SPECIFICATIONS ........................3 CATEGORY DEFINITIONS .......................... 3 IMPORTANT SAFETY WARNINGS ......................4 OVERVIEW ..............................5 SYMBOLS ..............................6 OPERATING INSTRUCTIONS AC/DC Voltage: <1000V AC/DC ....................6 Resistance: <40M ........................... 7 Continuity ............................7 Diode .............................. -
Page 3: Functions
FUNCTIONS • 1000V AC/DC • Audible continuity • 10A AC/DC • Capacitance 9999µF • Resistance 40M • Milliamps/Microamps • Diode test FEATURES • Auto/Manual ranging • Test lead holders • Auto power off • Kick stand • Min/Max • High resolution backlit display •... -
Page 4: Important Safety Warnings
IMPORTANT SAFETY WARNINGS WARNING Read entire Safety Notes section regarding potential hazards and proper instructions before using this meter. In this manual the word “WARNING” is used to indicate conditions or actions that may pose physical hazards to the user. The word “CAUTION”... -
Page 5: Overview
OVERVIEW ® RANGE MIN/MAX HOLD FAST A. Apo: Auto power off after 30 minutes of use. Press G. Category Max Indicator: Maximum CAT Rating for and hold the HOLD button while turning the meter on fused input jacks. to disable Apo. •... -
Page 6: Symbols
SYMBOLS Negative AC/DC Voltage or Current Low Battery Maximum measured Overload: Range Exceeded Auto power off Active value displayed Minimum measured µF Hold/Capture Value Microfarad value displayed Voltage Amps Diode Microamps milliamps Ground nano Farads Ohms/Resistance Dangerous Levels Continuity Warning or Caution Auto Selection Auto Fuse... -
Page 7: Resistance: <40M
Resistance: <40M ® RANGE MIN/MAX HOLD FAST Features: HOLD RANGE MIN/MAX WARNING • Do not measure resistance on a live circuit. Ranges Accuracy Resolution Overload Protection 600 to 6M ±(0.8% +5 dgts) 0.1 to 0.001M 600V ±(1.5% +5 dgts) 0.01M Continuity ®... -
Page 8: Diode
Diode BAD DIODE GOOD DIODE Open Diode Displays "OL" Both directions ® Forward Bias Displays approx. RANGE MIN/MAX HOLD FAST voltage drop '0' Both directions (shorted) • Forward voltage drop if forward biased. • “OL” if reverse biased. Features: MIN/MAX HOLD Open Circuit Voltage Overload Protection... -
Page 9: Ac/Dc Microamps: 6000Μa
AC/DC Microamps: 6000µA AC/DC Milliamps: 400mA ® ® µ A RANGE MIN/MAX HOLD RANGE MIN/MAX HOLD FAST FAST Features: MIN/MAX HOLD RANGE ACµA Ranges Accuracy Resolution Overload Protection 600µA to 6000µA ±(1.2% +5 dgts) 0.1µA to 1µA 600mA /1000V Fast Fuse Minimum sensitivity: 50µA AC (auto selection mode only) DCµA Ranges... -
Page 10: Ac/Dc Amps: <10A
AC/DC Amps: <10A ® RANGE MIN/MAX HOLD FAST WARNING • Do not attempt to measure more than 10A AC. Features: HOLD RANGE MIN/MAX AC AMPS Ranges Accuracy Resolution Overload Protection 6A to 10A ±(1.5% +5 dgts) 0.001A to 0.01A 11A/1000V Fast fuse Minimum sensitivity: 500mA AC (auto selection mode only) CAUTION: 20A overload for 30 seconds max. -
Page 11: Battery Replacement
Battery Replacement • When the batteries are too low for safe operation, the Low Battery indicator will display. S/N: S/N: FCC/IC INFORMATION NOTE: This device complies with Part 15 of the FCC Rules and CAN ICES-3(A). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. -
Page 12: Warranty
WARRANTY The KANE505 is warranted to be free from defects in materials and workmanship for a period of 1 year from the date of purchase. If within the warranty period your instrument should become inoperative from such defects, the unit will be repaired or replaced at Kane’s option.