Download Print this page
Focus MC-760R Installation Manual

Focus MC-760R Installation Manual

Pir intrusion detector

Advertisement

Quick Links

1. Introduction
MC-760R series Detector is a digital micro-processing dual-tech
detector adopting the technology of DMF (Digital Memory Focus),
DMT (Dynamic Matrixing Time). The PIR parts adopt column
lens to increase the effect of energy-receiving. The MW parts adopt
advanced plane antenna microwave transmission and four-layered
screening technology, Its advanced anti-pets function can prevent
wrong alarm to a 15 KG pet or 8 cats, insects, mice or birds etc. MC-760R
has overcome the interference that common detector can't prevent , and
it w o n ' t t r i g g e r wrong alarm or miss a l a r m s o i t i s f a r e x c e l l e n t i n
f u n ction than common detectors. With the buit in large capability
battery and the exclusive electricity save up model, it can be used for
a long time of as twice as the other brand detectors.
2.Specifications
Models
MC-760R
Detection Range:10
m*10m
Input Voltage:3 VDC
Current Drain:About 20 mA (common)
5mA(alarm)
PIR Section:Lens Date
NO.of Curtain Beams 11+
5 (Typical)
Max.Coverage
1 *1 m /90
2
2
Tripping Indication:
lndicator lights for about 10 seconds
Alarm indication:
The LED lighting for 2-3 second
3.Installation
3.1 General Guidelines
Within the detecting
Don't face cold
range, the windows
or heat directly
cannot be opened
3.2Anti-pests installation
The upper part of the
detection area is non
anti-pests area
,
,
,
,
,
,
20
30
0
10
40
50
,
9m
40
,
6m
26
,
13
3m
,
0
,
3m
13
,
6m
26
,
9m
40
0
3m
6m
9m
15m
12m
DFM-235D Top view
,
7.5
2.3m
,
5
1.5m
,
0.6m
2
,
,
,
,
,
50 ,
0
10
20
30
40
3m
6m
9m
12m
15m
DFM-235D side view
Can not be installed
in the open air
Never face the detector to
the place that pests can
climb up directly
LED
PIR Lens
Picture 1:
appearance
Mounting
Surface or corner,at the height of 1.8 to 2.4 m
Note: Base allows single-sided corner mount at 45 to wall
Accessories:
BR-1:Surface mounted swivel bracket, adjustable 30
down and 45
left or right.
BR-2:BR-1 with a corner adapter
BR-3:BR-1 with a ceiling adapter
Environment:
Operating Temperature: -10 C to 50 C(14 F to 122 F )
Storage Temperature :-20 C to 60 C (-4 F to 40 F)
Anti white light :
9 0 0 0 LUX
Physical
Size(H*W*D):
4
m m
This device is coherent to Europe parliament direct 1999/5/EC
necessary items and rules, and also coherent to the main spirits
of radio and telecom terminal equipments on March 9 . 1999.
The device also reaches the Canadian standard RSS-210. It can
be used indoor and outdoor, which can reach its maximum prote-
ction and avoidance of above interference.
Wire connection or
Don't face the sun-
detector can't be near
shine directly
to high-pressure cable
Anti-mask
MW
LED
PIR
MW sensitivity
adjustor
Coding switch
Picture 2:
internal structure
th
Don't install on a
unstable base.
The installation height
of the detector is 1.8-2.4
meters can Anti-pests
SHEN ZHEN MEIANTECH CO;LTD

Advertisement

loading

Summary of Contents for Focus MC-760R

  • Page 1 Its advanced anti-pets function can prevent wrong alarm to a 15 KG pet or 8 cats, insects, mice or birds etc. MC-760R has overcome the interference that common detector can't prevent , and it w o n ' t t r i g g e r wrong alarm or miss a l a r m s o i t i s f a r e x c e l l e n t i n f u n ction than common detectors.
  • Page 2 3.3Illustrated Installation Procedure 3.3.1 Disassemble unit 3.3.2 Mount base 1.8-2.4m 6-8ft above ground A. Mark the drilling points and drilling the wall B. Route the wires into the Single side 45 base VIA the rear channel angled side C. Insert two dowels and Surface attach the base to the wall mount...
  • Page 3 3.10 Perform motion test to the detection area: install the cover and close the fasten part (refer to the right diagram) 1. Start the test at least 2 minutes after power supply 2. Crossing to any direction of the detection area, your walking with 0.75m/s will cause the LED indicator to light for 2-3 seconds (refer to the right diagram) 3 .Perform motion test from contrary directions in order to confirm...
  • Page 4 5 Solution of usual problem In alarm area, have walk test but no alarm output To check if the control main To disconnect the alarm To open the detector Alarm LED lights up, board faulty. If yes, contact cabin, check the relay output wire from the terminal, without alarm signal the supplier of mainboard.