Une ZHERO Manual
Hide thumbs
Also See for ZHERO:
- Manual (129 pages) ,
- Quick installation manual (9 pages) ,
- Quick installation manual (8 pages)
Related Manuals for Une ZHERO
Summary of Contents for Une ZHERO
- Page 1 ZHERO Installer Tool MANUAL Ver. 0.1 UNE SRL - VIA MODENA 48/E – 42015 CORREGGIO (RE) - ITALIA - PI 02513460358 - T.+39 0522 693566 - F. +39 0522 1483326 - INFO@UNESRL.COM – https://unesrl.com...
-
Page 2: Table Of Contents
4.3.3. Firmware table ............................... 7 4.3.4. Variables table ............................... 7 4.4. “SETTINGS” section .............................. 8 4.4.1. Sale on net ..............................8 4.4.2. Batteries ................................. 8 4.4.3. Controllers ..............................9 4.4.4. Date and time ZHERO ............................ 9 CLOSING OF THE PROGRAM ........................... 9... -
Page 3: Information About This Document
Installer Technician This manual contains the instructions for using the software “ZHERO Installer Tool”, both for verification of the correct installation, and the analysis of the operation. The original language of this document is Italian, in case of inconsistencies or doubts, request the original document to UNE srl. -
Page 4: Istruction For Accessing The Usb Port
• Be sure to always operate safely and remove the parts of the carpentry only in absence of dangerous voltage; • Remove the “UNE” plate that covers the switches; • Remove the ZHERO main panel (Fig. 2); • Locate the hole in the upper part of the carter, with the words: “USB PC” and connect the cable (the USB is in position indicated by the image) (Fig. -
Page 5: Starting The Program And Configuring The Com-Port
4.1. INTALLATION OF THE PROGRAM • Double-click the setup entry in the program folder; • Click “Next >” in the installation window of ZHERO Installer Tool; • If necessary, indicate the installation folder of the (usually automatically detected); • Press again “Next >” to confirm the installation;... -
Page 6: Main" Section
Select the language chosen in the bottom right; b) Click: “Refresh list” top right; c) From the drop-down menu select the COM marked as follows: “COM… UNE ZHERO S6”; Press “OPEN” e and make sure that “Connected” appears in the status section. -
Page 7: Operation" Section
On Grid: inverter ON and connected in parallel to the grid (Standard working mode); • Off Grid: inverter ON but not connected to the grid; • Bypass: ZHERO connected to the grid but inverter OFF; • ERROR: abnormal working mode (both inverter and Grid disconnected). 4.3.2. Working state •... -
Page 8: Firmware Table
4.3.3. Firmware table • Boot - Firmware bootloader and firmware CPU; • Fw Major – Fw minor Inverter firmware; Inverter • Fw Major – Fw minor Controllers firmware; Controller • Batteries Firmware Batteries firmware. Battery 4.3.4. Variables table • User consumption (kW): power used by the user; o Main (kW): power under wattmeter (no backup) o Backup (kW): power under backup line •... -
Page 9: Settings" Section
The allowed modifications permit to change the system configuration in case of UNE ZHERO Upgrade/Downgrade. 4.4.1. Sale on net Put or remove the check “Enable sale on net” and press: Save; at the end, the UNE ZHERO system must be restarted to make the changes effective. 4.4.2. Batteries The system automatically recognizes the type of battery installed: the additional battery must be of the same type as the one installed. -
Page 10: Controllers
In this section you can set the date and time of the ZHERO system if this is not set correctly. The first box shows the date and time set on ZHERO, in the menu below: “New date and time” it is possible to set the value to be acquired;...