Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jobsite CT0827
Summary of Contents for Jobsite CT0827
- Page 1 115MM ANGLE GRINDER CT0827 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address:20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 115MM ANGLE GRINDER Model: CT0827 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards：... -
Page 3: Technical Specifications
1. TECHNICAL SPECIFICATIONS Model: CT0827 Voltage: 220 -240V~ 50 Hz Power consumption: 900 W Rated speed: 12000min Drive spindle diameter Max disc diameter: 115 mm Disc thickness 6mm for grinding disc Sound pressure level L 90.7dB(A) K=3dB(A) Sound power level L 101.7dB(A) -
Page 4: General Power Tool Safety Warnings
2. GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 5 inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Page 6 these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
- Page 7 such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute.
- Page 8 ignite these materials. p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Kickback And Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad or any other accessory.
-
Page 9: Specific Safety Rules
Safety Warnings Specific For Grinding : a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b)The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. -
Page 10: Technical Description
-Do not use separate reducing bushings or adapters to adapt large hole abrasive wheels; -For tools intended to be fitted with threaded hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length; -Check that the work piece is properly supported; -Do not use cutting off wheel for side grinding;... -
Page 11: Unpacking And Checking
5. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the air tool. - Page 12 lock lever. Make sure that the fastening lever is properly locked after setting the guard. To remove the protective cover, follow the installation procedure in reverse. The protective cover can be turned to a desired angle, but not more than 45° on left side or right side.
- Page 13 off the machine. WARNING: Do not cover exhaust vents when the tool is in use. This may cause damage to the motor and reduce the efficiency of the tool. Abrasive operation When equipped with abrasive wheel and guard, for the best work results hold the grinder at 15~20°to the work piece.
-
Page 14: Description Ofthe Symbols
8. DESCRIPTION OFTHE SYMBOLS The use of symbols in this manual is intended to draw your attention to possible risks. The safety symbols and the explanations that accompany them must be perfectly understood. The warnings in themselves do not remove the risks and cannot replace correct actions for preventing accidents. -
Page 15: Parts Diagram
10. PARTS DIAGRAM... - Page 16 Description Description Bearing set Nut M8 Bearing φ7 x φ19 x 6 Cord clamp Armature Housing Check ring φ10 Stator Screw M5 x 8 washer φ4 Bearing φ26 x φ10 x 8 Screw ST4.2 x 62 Stop pin Fan guide Spring Brush holder Gear box...
Need help?
Do you have a question about the CT0827 and is the answer not in the manual?
Questions and answers