Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Jobsite CT1649
Summary of Contents for Jobsite CT1649
- Page 1 230MM ANGLE GRINDER CT1649 Ref no. S1M-ZP15-230 INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE. Cannon Tools Limited Address:20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM...
- Page 2 In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 230MM ANGLE GRINDER Model: CT1649 (Ref no. S1M-ZP15-230) Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards：...
-
Page 3: Product Specifications
PRODUCT SPECIFICATIONS CAUTION Carefully read through this entire instruction manual before using your new power tool. Take special care to heed the Cautions and Warnings TECHNICAL DATA Model No. CT1649 Voltage: 230-240V/50Hz Power 2380W No Load Speed 6600/min Disc diameter 230mm... -
Page 4: Power Tool Safety
POWER TOOL SAFETY SAFETY INSTRUCTIONS safety precautions including the following, To use this tool properly, you must observe should always be followed to reduce the risk the safety regulations, the assembly of fire electric shock and personal injury. instructions and the operating instructions to Also please read and heed the advice given be found in this manual. - Page 5 POWER TOOL SAFETY use tools for purposes not intended; do not and cutters, and when the tool is not in use circular saws to cut tree limbs or logs. use. 8. Dress correctly. 16. Remove adjusting keys and Do not wear wrenches.
- Page 6 POWER TOOL SAFETY 22. Have your tool repaired by a years operate this tool. qualified person. This electric tool is in Rags, cloths, cord, string and the like accordance with the relevant safety should never be left around the work area. requirements.
- Page 7 POWER TOOL SAFETY Do not use separate reducing bushings or discs. Cheap or poor quality discs tend to adaptors to adapt large hole abrasive glaze up which loads the motor and can wheels. damage it. Use discs for their designated ...
-
Page 8: Know Your Product
KNOW YOUR PRODUCT Before using the angle grinder, familiarise yourself with all the operating features and safety requirements. Use the tool and accessories only for the application intended all other applications are expressly ruled out. 1 Motor housing 5 On/Off switch 2 Spindle lock button 7 Power cord 3 Disc guard... -
Page 9: Controls And Operation
CONTROLS AND OPERATION CONTROLS 1/ Looking at the angle grinder from the top, the spindle lock (2) is located at the front 6/ Allow the grinder to start and attain full top right hand side. speed before bringing the grinder to the work 2/ There are attachment points (4) for the piece. - Page 10 FITTING GRINDING DISC FITTING A GRINDING DISC angle grinder. The spigot section must Caution.: Switch off the grinder and locate with the hole disconnect it from the power point. in the grinding disc. 1/Turn the angle grinder on to its back and press Hand tighten the outer flange until the spindle lock button.
-
Page 11: General Inspection
GENERAL INSPECTION kilowatts farads 1/ Regularly check that all the fixing microfarads Screws are tight, particularly the outer Hours flange. They may vibrate loose over time. minutes 2/ The supply cord of the tool and any seconds extension cord used should be checked No load speed frequently for damage if damaged have the cord set replaced by an authorised... -
Page 12: Parts Diagram
PARTS DIAGRAM... -
Page 13: Parts List
PARTS LIST Component Quantity Component Quantity Flange Bearing Flange nut Armature Spanner Bearing Washer Bearing set Shield Screw Washer Oil envelop Fan guide Spindle Stator Screw Housing Spring washer Name plate Front cap Screw Bearing Left brush cap Screw Brush holder Gear Brush spring Bearing... - Page 14 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in china...
Need help?
Do you have a question about the CT1649 and is the answer not in the manual?
Questions and answers