Page 1
Laser Engraver USE Manual Model :M500 R E D S A I L T E C H C O . , L T D...
Page 2
This Category of laser cutting machine is GB4 laser products. Please pay attention to the laser radiation while operating, and avoid your eyes and skin from being exposed to direct or scattered laser radiation.
Chapter Six Equipment Maintenance and Notes 6.1 Ground Wire Link........................14 6.2 Equipment Maintenance......................15 6.3 Equipment Notes........................17 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
2. Be sure to put the equipment enclosure grounding correctly. The scope of this manual to be used: This manual applies to our company M500 series laser cutting machine products. 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n...
7·Ventilator installation area 8·Output power strip area 9·Water Pump and Air Pump Installation Area 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
(1) Please full the tank with water before connecting(water level should be more than three-quarters of the water tank, submerged pump). 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
1. ventilator 2. Power input plug (220V) 3. The device ventilation slots 4.220V output power outlet 5. Air outlet 6. The vent pipe 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
The lamp (1) is mounted to its holder in the device (2), and make the lamp power plug into the lamp slot. 3.5 Power main control switch zone description of device 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
Adjust optical path: The important step in using laser engraving machine is adjust optical path . 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
Page 12
(X direction) position so that the first lens reflex reflected light hit on the second mirror (center). (See Figure 9) 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
Page 13
(center is better). (Please see Picture Laser head The second mirror frame 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
Page 14
After adjust the light path, use the focus plate measuring the focal length, after that, the article can be processed。(Figure12) (Figure12) 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
。In order to ensure personal safety of operator and the normal operation of the 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
。 3rd 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...
Page 17
,it will affect the stability of mechanical motion,so it need observe if there are any abnormal sound or anomalies for transmission components during machine works,Identify 济南红帆科技有限公司 h t t p : / / w w w . e a s y c u t . c n Redsail Tech Co., Ltd...