Advertisement
2. SPECIFICATIONS
HVF14
Fan diameter
14”
Power supply
230V
Motor
70W 50Hz
3. ASSEMBLY & OPERATING
3.1.
ASSEMBLY.
Unpack carton and assemble the fan as follows:
3.1.1. Remove the holding screw (fig 1.2) from the rear of the fan control box (1).
3.1.2. Push the fan control box fixing pin (4) through the hole in the right leg of the fan base (3).
3.1.3. Fix with the holding screw (2) and firmly tighten the fan control box onto the leg.
NOTE: Ensure you install the control box with the power lead (5) running directly from the rear
of the fan motor around the right leg to control box and not tucked under or through the base leg.
3.2.
FAN OPERATION.
WARNING! Ensure you read, understand and apply safety instructions before using fan.
3.2.1. Use handle to carry the fan and place in a suitable location.
p
3.2.2. Check that the speed control box (1) is set to “0” (off), plug into the mains power supply
and switch the power on.
3.2.3. The Fan has three speeds in order to meet various air circulation
requirements. Settings “1” (Low) and “2” (Medium) should meet most
workshop needs. For maximum output select speed “3”.
3.2.4. Adjust the air stream by moving the base from side to side and tilting the fan up or down.
3.2.5. When you have finished using the fan ensure you turn the speed control switch to “0” (off) and disconnect the fan from mains power.
4. CARE OF FAN
WARNING! Ensure the fan is disconnected from the mains power supply before attempting any of the following:
4.1.
Use a soft, damp cloth to clean the fan.
DO NOT immerse the fan in water and never allow water to drip onto the motor housing.
DO NOT use solvents, petroleum, paint thinner or other chemicals to clean the fan.
4.2.
To clean the fan blade, use 2 screw drivers to disengage the hooks (fig 2.) which hold
the front and back grills together. Remove the front grill and wipe the blade and inside the grill.
Reassemble the fan by snapping the front grill into place.
4.3.
Should the motor, speed control box or the power leads require service or
maintenance contact your local service agent.
4.4.
When not in use place the fan in its original box or cover the fan to protect
from dust, and store in a safe, dry, childproof location.
Declaration of Conformity
HIGH VELOCITY FAN
Models HVF14 & HVF18
EN 60335-2-80
89/336/EEC Electromagnetic Compatibility
73/23/EEC Low Voltage Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue on 01284 757525 and leave your full name and address including your postcode.
HVF18
Fan diameter
Power supply
Motor
We, the sole importer into the UK, declare that the products listed below
The construction files for
Jack Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
18”
230V
170W 50Hz
these
products are held by the Manufacturer and may be inspected on request by contacting
01284 757500
01284 703534
fig 1
fig 2
are
in conformity with the following EEC standards and directives
For Jack Sealey Ltd.
Sole importer into the UK
16th February 2000
of Sealey
E-mail: sales@sealey.co.uk
HVF14, HVF18. - (1086) - (1) 160200
Power Products
Advertisement
