Quoizel WWD8407IB Installation Manual

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base bulb 100W Maximum, bulb not included.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Missing Parts? Contact your original place of
purchase.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar
A Assembly
x 1
-
STEP 1 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
Outlet Box
Figure 1
-
STEP 2 Test Fit the
Backplate to the Crossbar
Assembly
A. Remove the mounting balls
from the Crossbar
Assembly (A). Place the
backplate and Fixture Body
(B) onto the Crossbar
Assembly (A) and secure
with mounting balls. Note:
The backplate and Fixture
Body (B) should be snug
against the wall and held
tight with the mounting
balls. If it is not, adjust the
length of the mounting
2018 QuoizelInc.
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
B
x 1
Supply Wires
with Ground Wire
A
Outlet Box Screws
(not included)
Backplate
Mounting Screw
A
Hex Nut and
Lock Washer
Figure 2
visit us on-line at www.quoizel.com
Installation Guide #IS-WWD8407IB
For Style WWD8407IB
Care + Maintenance selection.
(Step 2 Continued)
screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate and Fixture Body (B) is secure,
remove the mounting ball and Fixture Body (B) and proceed to
Step 3.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
STEP 4 - Install the Fixture
Body
A. Position the backplate and
Fixture Body (B) onto the
Mounting
Crossbar Assembly (A).
Ball
Place the holes in the
backplate over the
mounting screws. Secure
the Fixture Body by using
B
the mounting balls and
hand tighten the mounting
balls until snug.
1of2
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Green Ground Screw
on the Crossbar
Mounting Screw
A
Figure 4
ReleasedDate:2018-04-04
Figure 3
Backplate
Mounting
Ball
B