Table of Contents
Advertisement
Quick Links
Application
The AM24 actuating drive with 2-point or 3-point control is used to control air
dampers with fail-safe operation in ventilation and air conditioning systems.
The drive is equipped with a universal terminal block and is mounted directly
on the air damper axle.
The actuating drive is overload resistant. When the valve or motor stop is
reached, the motor stops automatically.
Type
AM24
AC 24 V actuating drive with 2-point or 3-point control,
torque 18 Nm
Technical data
Mains
Nominal voltage
Functional range
Control
2-point or 3-point signal
Connection
Cable 1 m long, 3 x 0.75 mm² or terminal connection
Torque
18 Nm at nominal voltage
Rotational angle
Max. 95°, adjustable limit 33.3..95% rotational angle
Rotational direction Set using rotational direction switch CCW/CW
Position indicator
Arrow on actuating drive
Run time
100..150 s with 0..18 Nm
Manual setting
Press button
Degree of protection IP54 with cable entry from below
Ambient
temperature
-30..+50°C
Weight
1.3 kg
M aintenance
Maintenance-free
Accessories
AV10/18 Axle extension 240 mm for valve axles
Ø 10..18 mm or square axles SW10.. 14
ZG/AM
L90
PA1000
SA2
Installation
Electrical installation and unit connection may only be carried out by qualified
technicians.
Install the actuating drive in accordance with VDE guidelines and local regulations.
Caution
The unit is connected according to the terminal connection diagram or the legally binding system circuit
diagram.
Wiring diagram
2 -point control
AM24
1
2
0 V
24 V
AC
Connection using safety transformer
Connection using pre-assembled cable. For direct terminal connection, see page 2.
Kieback & Pete
r GmbH & Co KG
Tempelhofer Weg 50
12347 Berlin/Germany
Telephone: +49 30 60095-0, Fax: +49 30 60095-164
www.kieback-peter.de, info@kieback-peter.de
AC 24 V, 50/60 Hz, 4.5 VA
AC 19.2..28.8 V
Pivot lever with 2 KG8 ball joints, with
accessories
Universal valve lever
Feedback potentiometer 1000 Ω
Auxiliary switch, floating, 6 A (1.5 A), AC 250 V
3 -point control
AM24
Core
Aderbe-
3
1
designation
zeichnung
0 V
Dimensions
Core
Aderbe-
2
3
designation
zeichnung
24 V
AC
Technical Data Sheet 3.50-31.018-01-en
AM24 Actuating Drive
Rotational direction switch
Button
R otation direction
Connection
Rotational direction switch
Off
Off
Advertisement
Table of Contents
Related Manuals for Kieback&Peter AM24
Summary of Contents for Kieback&Peter AM24
- Page 1 Application Rotational direction switch The AM24 actuating drive with 2-point or 3-point control is used to control air dampers with fail-safe operation in ventilation and air conditioning systems. The drive is equipped with a universal terminal block and is mounted directly on the air damper axle.
- Page 2 AM24 Actuating Drive Device Description The AM24 actuating drive is normally connected using the pre-assembled flexible connecting cable. To connect the connection line from the drive to connection line of the control unit, use a connection socket provided on-site. However, it is also possible to connect the actuating drive directly to the connection line from the control unit. In this case, the connection socket provided on-site is not needed.
- Page 3 Technical Data Sheet 3.50-31.018-01 Device Description AM24 Actuating Drive Mounting Mounting with a valve that closes counterclockwise Place the actuating drive onto the valve shaft (1), close the valve (2) and hand- (Valve shaft at least 48 mm long) tighten the clamp (3) Adjust and mount the supplied locking Press button (1).
Need help?
Do you have a question about the AM24 and is the answer not in the manual?
Questions and answers