Front Panel Controls - Harman Kardon AVR 320 Owner's Manual

Front Panel Controls

1
2
5
3
4
1 Main Power Switch 1 Main Power Switch
2 System Power Control 2 System Power Control
3 Power Indicator 3 Power Indicator
4 Headphone Jack 4 Headphone Jack
5 Dolby Mode Selector 5 Dolby Mode Selector
6 DTS Surround Mode Selector 6 DTS Surround Mode Selector
7 Logic 7 Mode Selector / 7 Logic 7 Mode Selector /
Button Button
‹ ‹
8 Tone Mode 8 Tone Mode
9 Surround Mode Selector 9 Surround Mode Selector
) Tuning Selector ) Tuning Selector
! Tuner Band Selector ! Tuner Band Selector
1 Main Power Switch: Press this button to
apply power to the AVR 320. When the switch
is pressed in, the unit is placed in a Standby
mode, as indicated by the amber Power
Indicator 3 surrounding the System
Power Control 2. This button MUST be
pressed in to operate the unit. To turn the unit
off and prevent the use of the remote control,
this switch should be pressed until it pops out
from the front panel so that the word "OFF"
may be read at the top of the switch.
NOTE: This switch is normally left in the "ON"
position.
2 System Power Control: When the Main
Power Switch 1 is "ON, " press this button
to turn on the AVR 320; press it again to turn
˘ ¯
7 9
6 8
)
@ Set Button @ Set Button
# Preset Station Selector # Preset Station Selector
$ Stereo Mode Selector / $ Stereo Mode Selector /
% Input Source Selector % Input Source Selector
^ FM Mode Selector ^ FM Mode Selector
& DTS Neo:6 Mode Selector & DTS Neo:6 Mode Selector
* Digital Optical 3 Input * Digital Optical 3 Input
( Input/Output Status Indicator ( Input/Output Status Indicator
Ó Digital Coax 3 Jack Ó Digital Coax 3 Jack
Ô Video 4 Input Jacks Ô Video 4 Input Jacks
 Bass Control  Bass Control
the unit off. Note that the Power Indicator
3 surrounding the switch will turn green
when the unit is on.
3 Power Indicator: This LED will be lit in
amber when the unit is in the Standby mode to
signal that the unit is ready to be turned on.
When the unit is in operation, the indicator will
turn green.
4 Headphone Jack: This jack may be used to
listen to the AVR 320's output through a pair of
headphones. Be certain that the headphones
1
have a standard / " stereo phone plug. Note
4
that the main room speakers will automatically
be turned off when the headphone jack is
in use.
˜ ˆ
! % &
#
@ $ ^ *
Ò Balance Control Ò Balance Control
Ú Treble Control Ú Treble Control
Û Digital Select Button Û Digital Select Button
› › Button Button
Ù Channel Select Button Ù Channel Select Button
ı Volume Control ı Volume Control
ˆ Input Indicators ˆ Input Indicators
˜ Main Information Display ˜ Main Information Display
¯ Remote Sensor Window ¯ Remote Sensor Window
˘ Surround Mode Indicators ˘ Surround Mode Indicators
5 Dolby Mode Selector: Pressing this selec-
tor button cycles the AVR through the various
Dolby surround modes. The first press of the but-
ton switches the surround mode to the last
Dolby surround mode that was in use. Each sub-
sequent press selects the next mode in the fol-
lowing order:
6 DTS Surround Mode Selector: Pressing
this selector button cycles the AVR through the
DTS surround modes. The first press of the but-
ton selects the last DTS surround mode that
ı
Ô
(
Ó
DOLBY
DOLBY PRO LOGIC II MUSIC
DIGITAL
DOLBY PRO LOGIC II DOLBY PRO LOGIC II
EMULATION
MOVIES
DOLBY 3 STEREO
5 FRONT PANEL CONTROLS
Ù
Û
Ú
Ò
