Table of Contents
Advertisement
https://appliancetechmanuals.com
to remove.
5. Remove the louver covers A, B, and C from the hood
REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven)
1. Disconnect the power supply cord, and uncoil the power
supply cord.
2. Remove the turntable tray and support from the oven
cavity.
3. Remove the one (1) screw holding the exhaust damper
assembly to the rear stay, and remove the exhaust
damper assembly by sliding it backward.
4. Remove the two (2) screws holding the oven (outer case
cabinet) to the top cabinet.
5. Remove the hood exhaust louver referring to "HOOD
Remove the oven from the wall and proceed as follows;
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove three (3) screws holding the hood exhaust louver
to the oven, and pull it forward to remove by pushing the
right and left tabs of the hood exhaust louver. (Refer to
procedure of "HOOD EXHAUST LOUVER REMOVAL".)
4. Remove four (4) screws holding the rear stay to the hood
fan motor or the oven, and remove it.
5. Remove the four (4) screws from the rear of the outer case
cabinet.
6. Slide the outer case cabinet back about 1 inch (3 cm) to
1. Disconnect the power supply cord, remove the oven from
wall, and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer Case Removal".)
And proceed as follows.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove one (1) screw holding the hood duct to the oven
cavity front flange.
5. Disconnect the stop switch harness from the chassis
support and disconnect the wire leads from the fan motor.
6. Lift up the fan motor side of the hood duct.
7. Disconnect filament leads of transformer from the
magnetron and capacitor.
8. Disconnect high voltage leads of capacitor from the
transformer.
9. Disconnect wire leads from transformer.
10.Remove two (2) screws holding the transformer to right
base plate.
HOOD FAN MOTOR, HOOD DUCT, OVEN LAMP SOCKET REMOVAL AND AH SENSOR REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal"
of the base model Service Manual)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
exhaust louver
6. Now, the hood exhaust louver is free.
EXHAUST LOUVER REMOVAL".
6. While supporting the front of the oven, unfasten the two (2)
unit mounting screws holding the oven to the unit mounting
plate.
7. Remove the oven by sliding it into the arms of the unit
mounting plate and pull the power cord out of the wall
cabinet.
8. The oven is now free and can be placed on the work
surface selected for servicing the oven.
9. Installation is the reverse of this procedure.
OUTER CASE REMOVAL
free it from retaining clips on the cavity face plate.
7. Disconnect the three (3) pin connector of the power supply
cord from the wiring harness and remove the power supply
cord together with the outer case.
8. Discharge high voltage capacitor.
CAUTION: 1. DISCONNECT OVEN FROM POWER
POWER TRANSFORMER REMOVAL
Re-install
1. Install by sliding the transformer on the right base plate
with its primary terminals toward the outer case.
2. Secure the transformer with two (2) screws to right base
plate.
3. Re-connect wire leads (primary and high voltage) to the
transformer and filament leads of transformer to magnetron
and high voltage capacitor. Refer to "PICTORIAL
DIAGRAM".
4. Re-install the hood duct holding the fan motor to the oven
cavity front flange with one (1) screw.
5. Re-connect the wire leads to the chassis support and the
fan motor, referring to "PICTORIAL DIAGRAM".
6. Re-install the outer case and check that oven is operating
properly.
CAUTION: MAKE SURE THE WIRE LEADS NEVER TOUCH
4. Disconnect the 6-pin connector of the hood fan motor
from the main wire harness located at the right edge of the
hood duct and release the snap band from the hood duct.
5. Remove the hood fan motor from the hood duct by lifting
it up.
6. Now, the hood fan motor is free.
33
SUPPLY BEFORE REMOVING OUTER
CASE.
2. DISCHARGE THE HIGH VOLTAGE
CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.
THE FAN BLADE.
PLMV169DCC
Advertisement
Table of Contents
