Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hanns.G HW192DPB
Summary of Contents for Hanns.G HW192DPB
-
Page 1: Tft Lcd Monitor
19 inch Wide Screen TFT LCD Monitor HW192 USER’S MANUAL... - Page 2 User’s Manual Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
-
Page 3: Table Of Contents
SAFETY NOTICE ... 4 PRECAUTIONS ... 4 SPECIAL NOTES ON LCD MONITORS ... 5 BEFORE YOU OPERATE THE MONITOR ... 6 FEATURES ... 6 CHECKING THE CONTENTS OF THE PACKAGE ... 6 INSTALLATION INSTRUCTIONS ... 7 POWER... 7 CONTROLS AND CONNECTORS... 8 ADJUSTING THE VIEWING ANGLE ... -
Page 4: Safety Notice
• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. -
Page 5: Special Notes On Lcd Monitors
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. -
Page 6: Before You Operate The Monitor
User’s Manual BEFORE YOU OPERATE THE MONITOR FEATURES • 19” Wide screen TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions: 1440 X 900 @60Hz ® • EPA ENERGY STAR • Ergonomic Design • Space Saving, Compact Case Design... -
Page 7: Installation Instructions
1. Align the monitor with the opening in the base. 2. Note that the longer section of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. -
Page 8: Controls And Connectors
CABLE CONNECTIONS: Turn off your computer before performing the procedure below. 1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 2. Connect one end of the 24-pin DVI-D cable (Dual input mode optional) to the back of the monitor and connect the other end to the computer’s DVI-D port. -
Page 9: Adjusting The Viewing Angle
• Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You may adjust the monitor for a viewing angle of 0° to 20° vertically and 0° to 30° horizontally. ROTATING THE MONITOR •... -
Page 10: Screen Height Adjustment
User’s Manual SCREEN HEIGHT ADJUSTMENT • Press the button in (1) direction, the monitor may be adjusted to the desired height freely. • Push the screen in (2) direction to lower the screen to its lowest position, the height will be fixed to that position and the button will lock automatically. -
Page 11: Operating Instructions
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. -
Page 12: Front Panel Control
(The Auto Adjustment function is used to optimized the H-Position, V-Position, Clock and Focus.) NOTES: • Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. •... -
Page 13: How To Adjust A Setting
User’s Manual HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness adjustment: Select the 「 Brightness 」 option on the 「 Main Menu 」 . Enter the option and adjust the level. Contrast adjustment: Select the 「Contrast」 option on the 「Main Menu」. - Page 14 User’s Manual OSD Diagram OSD Description Clock adjustment: Select the 「Clock Adjustment」option to reduce the vertical flicker of characters on the screen. Enter the option and adjust the level. Phase adjustment: Select the 「Phase Adjustment」option to reduce the horizontal flicker of characters on the screen.
- Page 15 User’s Manual OSD Diagram OSD Description How to set the OSD: Select 「OSD Setting」on the 「Main Menu」, and then enter the option. OSD horizontal adjustment: Select the 「OSD H-Position」option to adjust the horizontal position of the OSD. Enter the option and adjust the level. OSD vertical position adjustment: Select the 「OSD V-Position」option to adjust the vertical position of the OSD.
- Page 16 Enter the option and adjust the level. DOS mode: Select the 「DOS Mode」option to set the monitor for DOS display. Enter the option and select Text or Graphics. VGA mode: Select the 「VGA Mode」option to set the monitor for VGA display. Enter the option...
-
Page 17: Plug And Play
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. -
Page 18: Technical Support (Faq)
*Computer Video Card should be snugly seated in its slot *Make sure monitor’s video cable is properly connected to the computer. *Inspect monitor’s video cable and make sure none of the pins are bent. *Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. -
Page 19: Error Message & Possible Solution
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. -
Page 20: Appendix
***The above specification is subject to actual panel specification and is subject to change without prior notice. Note : The Maximum Resolution will depends on the display card supporting. Related issue can refer to www.hannsg.com FAQ section. 48.2cm(19.0") 0.2835mm(H) x 0.2835mm(V) 300cd/m... -
Page 21: Connector Pin Assignment
CONNECTOR PIN ASSIGNMENT 15 - Pin Color Display Signal Cable: PIN NO. DESCRIPTION Green Blue Ground Ground R-Ground G-Ground B-Ground 24 - Pin Color Display Signal Cable: (Dual Input Mode) PIN NO. DESCRIPTION TMDS Data 2- TMDS Data 2+ TMDS Data 2/4 Shield No Connection No Connection DDC Clock...