Page 1
Smart Energy Panel JPC 100-PRO User manual and technical data Janitza electronics GmbH Vor dem Polstück 6 35633 Lahnau | Germany Support +49 6441 9642-22 info@janitza.com | www.janitza.com...
Page 2
JPC 100-PRO JPC 100-PRO Smart Energy Panel Doc. no. 2.100.116.1.b 08/2022 The German version is the original version of the documentation.
Page 3
JPC 100-PRO Subject to technical alterations. The contents of our documentation have been compiled with great care and reflect the cur- rent state of the information available to us. Nonetheless, we wish to point out that updates of this document are not always possible at the same time as technical refinements are imple- mented in our products.
JPC 100-PRO Table of contents Information on the device and the user manual 1. 1 Disclaimer 1. 2 Copyright notice 1. 3 Technical changes 1. 4 About this user manual 1. 5 Defective device/disposal 1. 6 Conformity declaration Safety 2.
INFORMATION Janitza electronics GmbH assumes no This user manual describes the JPC 100-PRO liability for bodily injury, material damage or and provides information on how to operate financial losses which result from disregard of the device. Separate validities and distinctions the usage information.
Engage a certified disposal company to han- dle scrapping as needed. 1. 6 Conformity declaration The laws, standards and directives applied by Janitza electronics GmbH for the device can be found in the Declaration of Conformity on our website www.janitza.com.
JPC 100-PRO Safety The chapter on Safety contains information 2. 2 Hazard levels which must be observed to ensure your per- Warning and safety information is marked by sonal safety and avoid material damage. a warning symbol, and the hazard levels are...
Page 8
JPC 100-PRO Any unauthorized tampering with or use of WARNING the device, Risk of injury due to electrical voltage! • which goes beyond the mechanical, Severe bodily injury or death can result! electrical or other operating limits can lead...
JPC 100-PRO 2. 4 Hazards when handling the device 2. 5 Electrically qualified personnel in the switchboard cabinet To avoid bodily injury and material dam- When operating electric devices, it is un- age, only electrically qualified personnel are avoidable for certain parts of these devices permitted to work on the devices and their to conduct hazardous voltage.
• Measured value monitoring and configu- (e.g. falling from an elevated position, even ration of connected Janitza measurement without visible external damage, etc.). devices. 3. 3 Intended use...
JPC 100-PRO 3. 4 Scope of delivery Quantity Part no. Designation 15.06.3xx JPC 100-PRO Installation instruc- 33.03.871 tions INFORMATION All supplied options and design variants are described on the delivery note. 3. 5 Operating concept You can operate the device directly via the...
252 +1 4. 1 Installation location Fig. 03: Cutout dimensions JPC 100-PRO The device is suitable for installation in stationary and weatherproof switchboards For sufficient ventilation, observe the mini- indoors. mum distance of 20 mm (0.79 in) around the circumference to adjacent assemblies (to all sides and the back).
JPC 100-PRO 4. 3 Securing ATTENTION Mount the device on a flat, clean and burr- Material damage due to disregard of the free surface using the retaining brackets installation instructions. (Fig. 4). Unevenness can lead to damage Tightening the retaining brackets too tightly of the display and to the entry of dust and will damage the device.
5. 3 Connection of the measurement CAUTION devices Material damage due to disregard of the The JPC 100-PRO is connected to the mea- connection instructions! surement devices via the Ethernet. Disregard of the connection instructions can damage your device. Connect the JPC 100-PRO via the Ethernet...
JPC 100-PRO Initial commissioning and user interface INFORMATION For information on initial commissioning and the user interface, refer to the functional de- scription of your application.
• Device designation (see rating plate) • Software versions (see system settings for your application) • Supply voltage • An exact error description. 7. 3 Update An update can be imported via a connected PC or directly on the JPC 100-PRO.
JPC 100-PRO Technical data General Net weight Approx. 1.25 kg (2.76 lb) Dimensions 264.5 mm x 187 mm x 32.1 mm (10.41 in x 7.36 in x 1.26 in) Installation depth 26.6 mm (1.05 in) Backlight (LED) Brightness: typ. 430 cd/m (39.95 cd/ft Chip i.MX8M Mini 4 Cores, 4x 1.6 GHz ®...
Page 19
JPC 100-PRO Dimensional drawings The figures are for illustration purposes only and are not to scale. (Dimensions in mm). Fig. 7: Front view Fig. 8: Side view Fig. 9: Rear view...
Page 20
Janitza electronics GmbH Vor dem Polstück 6 | 35633 Lahnau Germany Tel. +49 6441 9642-0 info@janitza.com | www.janitza.com Doc. no. 2.100.116.1.b | 08/2022 | Subject to technical alterations. The current version of the document can be found in the download area.