Subscribe to Our Youtube Channel
Related Manuals for PSS TSC 1500
Summary of Contents for PSS TSC 1500
- Page 1 Models: 1500 Installation Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE UBLICATION 8 5 1 7 5 4 5 3 1 F E B U R A R Y 1 4 , 2 0 1 4...
- Page 3 TSC 1500 Table of Contents Section Page No. Introduction Cautions and Warnings Specification Sheet Installation Programming / Operation Trouble shooting...
- Page 4 The TSC 1500 was developed to provide the operator ease of control without the need for keys that can be lost, misplaced or broken. By creating a touch pad control station the operator can conveniently operate all equipment in the gymnasium easily and efficiently.
- Page 5 TSC 1500...
-
Page 6: Installation Instructions
4 by 4 by 2 1/2" deep box. Once the relay box and keypad have been located and properly mounted, wiring of the system can be accomplished. Refer to System Wiring Configuration drawing (Page 5+6) from Performance Sports Systems, Model TSC 1500 Total System Control. - Page 7 TSC 1500...
- Page 8 TSC 1500...
- Page 9 TSC 1500 NOTE: Master board shown. Slave board will not have +12V hooked to keypad. All +12V power is to be fed off of the master board to keep from back feeding power in the system when daisy chained.
- Page 10 TSC 1500 Sequence 1 - Connect keypad and relay box control wiring as follows: Communication wiring and Power wiring Communication wiring and power wiring must be twisted pair 18 gauge wire or twisted pair multi- conductor cable of 22 gauge or larger. Shielded wire must be used when running nearby fluorescent lighting loads or Variable Speed Drives (air handling units).
- Page 11 TSC 1500 Note: Shields of wires should only be grounded in the relay box. Not both places. Note: Supplied voltage must be constant. If not constant errors can occur. Sequence 2 - Connect device motors to relay box as follows:...
-
Page 12: System Setup
It is not designed to be installed in this manner and doing so will cause operation problems. Contact Performance Sports Systems at 800-848-8034 for questions or additional information concerning the TSC 1500 Total System Control installation. System Setup: Din Settings: Once the system is wired then it can be set up. - Page 13 TSC 1500 Din Assignment: Relay Board > > Keypad < K&&...
-
Page 14: Programming Guide
TSC 1500 Programming Guide After assignment sheets have been filed out then devices can be assigned to the different device types. Individual Assignment: Example no. 1 1) Enter 3 to activate device assignment. 2) Enter device type (backstop) 3) enter two digit code (01-99) This is device number ex. Backstop 01... - Page 15 TSC 1500 Press "9" to go back to command mode. Note that the Devices from 01-49 are up and down devices and Devices from 50-99 are on/off devices. Command Mode: How to activate a device (1)-Press "1" (LED will turn Solid Yellow), then enter three digit device code (001 through 160)(LED will flash green).
- Page 16 TSC 1500 How to assign Aux devices: (7)-Auxiliary device is defined as an on or off feature. The 1500 is capable of having 50 Aux devices total. Any Device relay can be turned into an Aux relay. The power being used for this relay must be landed in the (IN) section of the device relay terminal block.
- Page 17 TSC 1500 4321 Passcode : _____________ Notes:...
- Page 18 Performance Sports Systems 9200 E. 146 Street Noblesville, IN 46060 800-848-8034 www.perfsports.com...
Need help?
Do you have a question about the TSC 1500 and is the answer not in the manual?
Questions and answers