Table of Contents
Advertisement
LED UFO HIGH BAY
INSTALLATION GUIDE
IMPORTANT SAFETY INFORMATION:
Please read all the instructions below before installation.
Make sure that the supply voltage corresponds to the rated product voltage.
▶
The product must be installed by a qualified electrician in accordance with the
▶
National Electrical Code and corresponding local codes.
If the product is damaged, do not use it.
▶
WARNING
RISK OF PERSONAL INJURY – READ and follow all WARNINGS and
installation instructions. Keep or give to the owner for future reference.
Risk of cuts: Wear gloves to prevent cuts or abrasions when removing from
carton, handling, installing, and maintaining this product.
Risk of electric shock: This product must be installed in accordance with the
applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Risk of Fire: Minimum 194°F supply conductors. Consult a qualified electrician to
ensure correct branch circuit conductor.
ASD® assumes no responsibility for claims arising out of improper or careless
Installation or handling of this product.
ELECTRICAL SCHEMATIC DIAGRAM:
UHB2
L (live/hot) black
L
N
N (neutral) connect white
G
Ground connect green
Dimming wires (violet and grey) are used
Violet
Dim +
1-10 V
for wiring the microwave motion sensor-kit,
Pink
DIMMER
Dim -
ASD-UHB-MSK1. The Vaux (black/white)
12 V output wires are normally vacant. This
SMART
provides 12 V output for external modules to
Vaux (Black/White)
MODULE
achieve smart control (optional).
UHB2 high voltage
L1
L2
L2 (neutral) connect white
G
Ground connect green
Note:
The dimmer can also be replaced by an active 1-10 V voltage source
▶
signal or passive components like resistors and zener diodes.
Do NOT connect Dim- to be output V - or V +, otherwise the driver will
▶
not work properly.
If 1-10 V dimming is not used, Dim + should be open.
▶
When 1-10 V negative logic dimming mode and Dim + is open, the
▶
driver will output minimum current.
* The regular voltage 120-277 V fixtures can be alternatively powered without neutral by
two-phase circuit with phase-to-phase voltage of 208V (L1-120 V & L2-120 V).
WARNING: Phase-to-phase voltage should be less than 277 V (160 V per each phase) and
more than 120 V (70 V per each phase)! Do not confuse Regular Voltage fixtures of 120-277 V
with High Voltage ones of 277-480 V!
ASD LIGHTING CORP
E-mail: orders@asd-lighting.com
FIXTURE
Violet
L
Dim +
DRIVER
Pink
N
Dim -
Vaux (Black/White)
G
FIXTURE
L1
Violet
Dim +
DRIVER
L2
Pink
Dim -
G
Web site: www.asd-lighting.com
UHB22-MS with motion sensor
L (live/hot)
L
L
connect black
N (neutral)
N
N
connect white
Ground
G
G
connect green
FIXTURE
The sensor is designed to operate with a single fixture. Connecting multiple fixtures can
damage the sensor.
UHB2 with motion sensor kit
L
L (live/hot) connect black
N
N (neutral) connect white
G
Ground connect green
UHB2 with motion sensor kit master slave
Dim + (Violet)
Dim - (Pink)
MOTION
L (live/hot) connect black
L
SENSOR
N (neutral) connect white
N
Ground connect green
G
Model
100W
150W
120 V
3
2
UHB-MSK1
277 V
6
4
Model HV
150W
277 V
4
UHBHV-MSK1
480 V
6
UHB2 with motion sensor kit and battery back-up kit
MOTION
SENSOR
L
L (live/hot) connect black
N
N (neutral) connect white
G
Ground connect green
FIXTURE
UHB2 with battery back-up kit
Switch
L
L (live/hot) connect black
N
N (neutral) connect white
G
Ground connect green
FIXTURE
For most up-to-date spec sheets please refer to asd-lighting.com
English
Dim + (Violet)
Dim - Vaux - (Pink)
Dim - (Gray)
Vaux + (Black/White)
TERMINAL BLOCK CONNECTOR
Dim + (Violet)
MOTION
SENSOR
Dim - (Pink)
L
+
DRIVER
N
-
G
FIXTURE
FIXTURE
FIXTURE
DRIVER
DRIVER
Dim- Dim+
L N
Ground
Dim- Dim+
L N
Ground
X FIXTURES
200W
240W
300W
400W
500W
1
1
1
0
0
3
2
2
1
1
200W
300W
400W
500W
3
2
1
1
4
3
2
1
L switch
Red
Dim -
Pink
BATTERY
Dim +
Violet
L
BACK UP
Brown
N
Blue
G
G
N
DRIVER
L
Dim +
Dim -
L switch
Red
Dim -
Pink
BATTERY
Dim +
Violet
L
BACK UP
Brown
N
Blue
G
G
N
DRIVER
L
Dim +
Dim -
Advertisement
Table of Contents
