i-PRO WV-QED100 Operating Instructions

Operating Instructions
Included Installation Instructions
Ceiling Mount Bracket
WV-QED100
Model No.
• Before attempting to connect or install this product, please read these instructions carefully and
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
"<Control No.: C****>" used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Caution: Notice:
• Before attempting to connect or operate this • This product is not suitable for use in loca-
product, please read these instructions care- tions where children are likely to be present.
fully. • Do not install this product in locations where
ordinary persons can easily reach.
• For information about screws and other parts
required for installation, refer to the corre-
sponding section of this document.
Precautions
„ Do not use this product except with suitable cameras.
„
Failure to observe this may cause a drop resulting in injury or accidents.
„ Refer installation work to the dealer.
„
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
„ The measures of protection against a fall of this product shall be taken.
„
Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety
wire.
„ The screws and bolts must be tightened to the specified torque.
„
Failure to observe this may cause a drop resulting in injury or accidents.
„ Install the product securely on a ceiling in accordance with the installation instructions.
„
Failure to observe this may cause injury or accidents.
„ Do not rub the edges of metal parts with your hand.
„
Failure to observe this may cause injury.
When using this product, also read the "Precautions" described in the operating
instructions for the camera to be attached.
About notations
Some functions are expressed with the following notations in this document.
C Clear dome cover
G Smoke dome cover
Preface
This product is a ceiling mount bracket that is designed to mount the indoor PTZ type camera on a
ceiling. This bracket can be used for an area with weak pull-out strength such as plasterboard in a
double ceiling, and the embedded type makes the visible part of the camera smaller.
The latest information about the supported cameras
<Control No.: C0501>
Specifications
Ambient temperature: –10 °C to +50 °C {14 °F to 122 °F}
Dimensions: Maximum diameter ø190 mm x 212 mm (H)
{ø7-15/32 inches x 8-11/32 inches (H)}
Approx. 800 g {1.77 lbs.}
Mass:
Main body: Surface treatment steel sheet
Finish:
Decorative cover: ABS resin i-PRO white
Dome cover: Acrylic resin
Precautions for installation
„ In order to prevent injury, the product must be securely mounted to the ceiling
„
according to the Installation Guide of this product.
„ This product is designed to be used indoors.
„
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
„ Installation area for this product
„
Make sure that the installation area is strong enough to hold the total
weight of the camera assembly before installation.
The installation area shall have 180 mm {7-3/32 inches} or more
space behind the ceiling.
The thickness of the ceiling board for installation can range between
9 mm {11/32 inches} and 40 mm {1-9/16 inches}.
„ Make sure to remove this product if it will no longer be used.
„
Ns0522-0
Printed in China
Standard Accessories
Operating Instructions (this document) ....... 1 pc.
The following are for installation
Safety wire* ............................................... 1 pc. Template A ................................................ 1 pc.
Safety wire angle* ...................................... 1 pc. Template B ................................................ 1 pc.
Inner cover (WV-QAT100) .......................... 1 pc.
* The product is shipped in a state where the safety wire is attached to the safety wire angle.
Other items that are needed (not included)
Anchor bolt (M10)* ....................................2 pcs. Nut (M10) ................................................ 6 pcs.
* O ne anchor is used for securing the mounting base, and the other anchor is used for connecting
the safety wire. (See Step 4)
IMPORTANT
• Prepare anchor bolts according to the material and strength of the area where the product is
to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total
weight of the installed devices (including the camera body, ceiling mount bracket, anchor
bolts, and all other parts).
Parts and functions
Mounting base
Fixing screw to be used
for cover fall prevention
Hole for microphone cable
Rubber-made
microphone stand*
* If a tiepin type microphone is used, mount the microphone on the rubber-made microphone
stand. Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
Installation
Refer to the operating instructions of the camera for details on the camera installation
(including the camera mounting, cable connection and adjustment).
Step 1
Remove the decorative cover.
① Loosen the fixing screw (unremovable) to be
used for cover fall prevention.
② Turn the decorative cover counterclockwise to
unhook it from the hooks (3 positions) of the
camera mounting bracket, and remove it from
this bracket.
C
③ Take the inner cover out.
G
(Transmittance: approx. 50 %)
Step 2
Remove the camera mounting plate.
180 mm
{7-3/32 inches}
or more
Remove the screws (M4, 3 pcs.) and remove the
camera mounting plate by turning it counterclock-
wise.
Ceiling board: between
9 mm {11/32 inches} and Remove the tab of the camera mounting plate (a)
40 mm {1-9/16 inches}
from the hole of the mounting base (b) (2 positions).
Note:
• Keep the removed screws until using them in
Step 14.
Step 3
Put Template A (accessory) against the ceiling and make a hole.
① Make 4 holes of 12 mm {15/32 inches} in
diameter.
② Remove the center part from the template.
③ Make a hole of 160 mm {6-5/16 inches} in
diameter.
* The hole shape is shown below.
Step 4
Install two anchor bolts (M10 recommended) into the concrete
ceiling.
① Determine the anchor bolt length (for mounting base) by use of Template B (accessory).
② Position the nut (locally procured) by use of Template B. (The distance between the bottom
surfaces of the ceiling board and nut shall be 136 mm {5-11/32 inches}.)
less than 1 m {3.28 feet}
Camera mounting
Anchor bolt for
plate
mounting base
Anchor bolt for
safety wire
Template B
Decorative cover
Ceiling board
Dome cover
IMPORTANT:
• When the existing anchor bolt is used as an anchor bolt for connecting the safety wire, make sure
that the distance between the anchor bolt and camera mounting position is 1 m {3.28 feet} or less.
Step 5
① Mount a nut so that the safety wire
angle is secured on the anchor bolt.
② Remove the safety wire from the safety
wire angle.
③ Insert the groove of the portion ❶ of
the safety wire angle into the anchor
bolt.
④ Close the safety wire angle while
inserting the groove of the portion ❷ of
the safety wire angle into the anchor
bolt.
⑤ Connect the safety wire to the safety
wire angle again.
⑥ Engage the nut from beneath, and
Fixing screw to be used for secure the safety wire angle with top
cover fall prevention
and bottom nuts.
⑦ Engage another nut from beneath to
tighten and secure the nut that was
engaged from beneath in y in a
double nut fashion
Note:
• When the existing anchor bolt that
has been installed is used for con-
Hook
necting the safety wire, the use of 2
spacer nuts is helpful.
Step 6
Attach the safety wire to the mounting base as
Screw (M4, 3 pcs.)
shown in the illustration below.
(a)
Fix the hook of the
safety wire to this
Camera
product.
mounting plate
(b)
Step 7
ø12 mm {15/32 inches}
Ceiling face
(4 positions)
ø160 mm
{6-5/16 inches}
Template A
Step 8
① Engage the top of the mounting base with
the anchor bolt for the mounting base.
② Secure the mounting base by turning the
ceiling board fixing screws (4 places)
clockwise.
Turning the ceiling board fixing screws
clockwise provides ceiling board
tightening between the bottom of the
② Use a nut
mounting base and ceiling board fixing
① Determine the anchor bolt length bracket resulting in mounting base
securing.
Recommended tigtening torque:
0.78 N·m {0.58 lbf·ft}
136 mm {5-11/32 inches}
IMPORTANT:
• When securing the mounting base on the
Install the anchor bolt in the center of the hole
ceiling, make sure that the four ceiling
board fixing brackets are open as shown
in the figure.
③ Secure the top of the mounting base with
double nuts (locally procured).
Mount the safety wire angle (accessory) on the anchor bolt for the
safety wire and connect the safety wire (accessory) to the angle.
<Image of safety wire connection>
Existing anchor bolt
①
Safety wire
Nut
(locally procured)
Safety wire angle
⑥ ⑦
Upper side
Anchor bolt
❷
④Close
③Insert
②Remove
Safety wire
Lower
❶
side
Safety wire angle
⑤Connect
Spacer nuts
Spacer nuts
Safety wire
Safety wire angle
Existing anchor bolt
Attach the safety wire.
Roof space
Safety wire
(Accessory)
Cables
Ceiling board
Mounting base
Insert the mounting base into the hole made in Step 3.
Secure the mounting base.
Anchor bolt for safety wire
Anchor bolt for the mounting base
① Insert the anchor bolt
Nut (locally procured)
③
Double nuts
(locally procured)
Ceiling board
fixing bracket
(4 places)
Ceiling board Ceiling board
fixing screw
(4 places)
②
Turn clockwise