Page 1
SPEEDGUARD I FLATBED FALL PROTECTION SYSTEM OPERATORS’ INSTRUCTION MANUAL Keep this Manual with the SPEEDGUARD system at all times. This will allow new users to read it before installing and using the SPEEDGUARD system. It is the SPEEDGUARD owner’s responsibility to ensure that all workers installing and using this system are thoroughly trained.
Page 2
NOTICE BEFORE INSTALLING SPEEDGUARD SYSTEM: Read, understand and follow these instructions for installing and using system. Failure by installer or user to follow any or all of these instructions could cause serious injury or death! FALLS FROM TRUCK BED CAN CAUSE SERIOUS INJURY OR DEATH! This fall protection system must be installed by a person standing on the ground or floor.
Page 3
405459Z STAKE POCKET MOUNT SYSTEM 402336S 7.5 FT RAILGUARD 300738 404726S 68" RAILGUARD 405389 CART ASSEMBLY 402337S 5 FT RAILGUARD CORDLESS IMPACT 154115 WRENCH Speedguard I Pocket Mount Installation Instructions Page 4 Speedguard I Clamp Mount Installation Instructions Page 5...
Page 4
SPEEDGUARD I POCKET MOUNT INSTALLATION INSTRUCTIONS Use the charts and diagrams on pages 3 to guide your installations. Note the location of each stake pocket holder. FALLS FROM TRUCK BED CAN CAUSE SERIOUS INJURY OR DEATH This fall protection system must be installed by a person standing on the ground or floor.
Page 5
SPEEDGUARD CLAMP MOUNT INSTALLATION INSTRUCTIONS Use the tables and diagrams on pages 3 to guide your installations. Note the location of each stake pocket holder. FALLS FROM TRUCK BED CAN CAUSE SERIOUS INJURY OR DEATH This fall protection system must be installed by a person standing on the ground or floor. Step 1.
Page 6
Step 2: Insert Rails: (1) Insert one end of rail into the holder (2) then lift the other end of rail into the next holder. Refer to image on left for proper sequence. CAUTION Risk of back injury Maintain control of rail to avoid injury. Never attempt to lift a rail in the middle and try to insert both ends of rail into holder at the same time.
Page 7
Step 4: Add rear rail Insert one end of the 5 foot rail into the pocket holder then lift the other end of rail into the stairway pocket holder. CAUTION Risk of back injury Maintain control of rail to avoid injury. Never attempt to lift a rail in the middle and try to insert both ends of rail into holder at the same time.
Page 8
Clamp Placement Options Fig 2. Installation on “C” Channel Fig 1. Installation onto Trailer with bottom Trailer flat bottom on Channel. Channel is minimum ¼” thick Fig 3. If necessary to avoid obstacles below Fig 4. Installation of Clamp on thin-sided trailer, clamp can be disassembled inserted channel trailer sides.
Page 9
Clamp-On System Storage “Clamp-on” Clamp layout-front. “Clamp-on” Clamp layout-back. Rail Locking system. Storage of impact gun and battery.
Page 11
This card must be filled out completely and mailed within ten (10) days from date equipment is delivered or warranty is null and void. EQUIPMENT PURCHASED……………………………………………………………………………………….SERIAL NO…………..……………………… DATE DELIVERED……………………………. NAME OF PURCHASER…………………………………………………………….……….…….………….. ADDRESS………………………………………………………………CITY……………………………………………STATE……... ZIP……………………. PURCHASED FROM (DEALER NAME) …………………………………………………………………………………………….…………………………… ADDRESS………………………………………………………………CITY……………………………………………STATE……... ZIP……………………. Was a copy of the owner’s manual and operation instructions included with the above equipment? YES □...
Page 12
2601 Niagara Lane N, Plymouth, MN 55447 PHONE: 877.791.4446 http://www.garlocksafety.com...
Need help?
Do you have a question about the SPEEDGUARD I and is the answer not in the manual?
Questions and answers