Preparing The Connection - DeWalt DCE200 Instruction Manual

To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 11 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 15 and one hand on the tool neck
press tool.

Preparing the Connection


WARNING: Always follow the specific
manufacturer's installation instructions for press
tool attachments being used. It is the installer's
responsibility to ensure the compatibility of the
pipe and fittings used for the connection. Contact
the manufacturer for specific information on their
fittings system. Failure to follow all instructions and
warnings may result in property damage and/or serious
personal injury.
• Make sure to clear the work area of loose debris and any
other items that could hinder the pressing operation.
• Always ensure the work area is set up properly and that
the tool's connection is prepared according to the fitting
manufacturer's instructions.
• Follow the fitting manufacturer's instructions to make
sure the tubing is inserted properly into the fitting.
Pressing (Fig. A, D–F)

WARNING: To reduce the risk of serious personal
injury, inspect the jaw assembly for cleanliness, cracks
or other damage before beginning a press. Using a dirty
or damaged jaw assembly could result in improper
press connections that could lead to extensive property
damage. Return damaged jaw assembly to a D
service facility.

WARNING: To reduce the risk of serious personal injury,
prior to use, inspect workpieces for cracks, defects or
wear. Defective workpieces may shatter.

WARNING: Before turning on the press tool, be
sure hands are clear of the jaws.
Before beginning a press, check the fuel gauge to determine
whether the battery charge is sufficient to complete the
pressing operation.
nOTE: The tool will turn off automatically after two minutes
of no use.
10 into the tool handle, align the
16 , of the
1. Press jaw arms
the fitting.
2. Turn the tool ON by holding the power ON/OFF button
until all three LEDs (
3. Hold tool securely.
4. Press and hold the trigger switch
the cycle is complete, indicated by the ram automatically
returning to its original position.
5. When the press cycle is complete, the cycle complete
LED 22 will flash green for five seconds. If the press
cycle is incomplete, the cycle complete LED
red for five seconds. No action is possible until the user
presses the power ON/OFF button
6. If the battery dies or tool malfunctions during the press
connection, the rollers can retract by pressing the reverse
trigger switch
and allow the jaws to be opened.
7. Press the power ON/OFF button
then press the jaw arms to open the jaw set.
nOTE: If the tool does not complete the press
properly, read the Troubleshooting Guide or LED
Indications sections or take the tool to a D
service center.
nOTE: When pressing overhead, always confirm
workpiece and tool are secure before pressing.
nOTE: In the event of an incomplete press, press the
reverse trigger switch
remove the material.
Pressing with Press Ring and Actuator
Jaw (Fig. A, D–F)
1. Open ring arms
2. Press actuator jaw arms
and secure into the mating slots
3. Turn the tool ON by holding the power ON/OFF button
until all three LEDs (
4. Hold tool securely.
5. Press and hold the trigger switch
the cycle is complete, indicated by the ram automatically
returning to its original position.
6. When the press cycle is complete, the cycle complete
LED 22 will flash green for five seconds. If the press
cycle is incomplete, the cycle complete LED
red for five seconds. No action is possible until the user
presses the power ON/OFF button
WALT
7. If the battery dies or tool malfunctions during the press
e
connection, the rollers can retract by pressing the reverse
trigger switch
and allow the jaws to be opened.
8. Press the power ON/OFF button
then press the actuator jaw arms
jaw 17 and remove from the press ring
9. Open ring arms
remove it from the fitting.
nOTE: If the tool does not complete the press properly,
read the LED Indications section or take the tool to a
D WALT factory service center.
e
2 to open jaws 1 and place around
21 , 22 , 23 ) illuminate green.
5 (bottom trigger) until
8 .
6 (top trigger). This will retract the ram
8 to turn the tool OFF,
6 to open the press jaws and
19 to place open ring
2 to open the actuator jaw
20 of the ring arms
21 , 22 , 23 ) illuminate green.
5 (bottom trigger) until
8 .
6 (top trigger). This will retract the ram
8 to turn the tool OFF,
2 to open the actuator
19 to open the press ring
English
8
22 will flash
WALT factory
e
18 around fitting.
17
19 .
8
22 will flash
18 .
18 and
9