Download Print this page
Panasonic BT-MA900G Installation Manual
Panasonic BT-MA900G Installation Manual

Panasonic BT-MA900G Installation Manual

Rack mounting adapter for bt-lh900 series

Advertisement

Quick Links

ENGLISH
Installation Guide
Rack mounting adapter for BT-LH900 series
BT-MA900G
The BT-MA900G rack mounting adapter is designed to be mounted
on the model BT-LH900 series, a liquid crystal video monitor used in
commercial applications, and make it possible to install this monitor in
a standard 19-type rack.
By replacing the bottom panel of the BT-LH900 series with the
accessory panel provided with the adapter, this 5U type (initial status)
of video monitor which can be tilted upward or downward can be
turned into a 4U type of rack-mounted stationary type of monitor.
<Note>
Before using the rack mounting adapter to install the monitor, turn off
its power.
How to replace the monitor's bottom panel
1 While referring to the figure on the right, remove the total of 12
screws.
2 Loosen the four screws on the top panel, and remove the bottom
panel.
3 Replace the monitor's bottom panel with the accessory panel, and
use the screws removed in step 1 to secure it.
4 Tighten up the screws which were loosened in step 2.
How to install the monitor
5U type (tilting type)
1
Remove the eight blind screws from the BT-LH900 series.
(Refer to the instructions in the operation guide of the BT-LH900
series.)
2
Separate the main controls from the BT-LH900 series monitor.
(Refer to the instructions in the operation guide of the BT-LH900
series.)
3
Secure the now separated main controls to the adapter.
1 Pass the cable of the main controls through the hole
provided.
2 Secure the main controls using the screws.
1
2
4
1 Remove the four screws and remove the rear panel.
2 Secure the monitor to the adapter using the four screws
provided.
2
5
Use the four screws to secure the rear panel and plug the cable
of the main controls into the connector on the monitor. (Refer to
the instructions in the operation guide of the BT-LH900 series.)
SE0903AT2031 -FJ @
Printed in Japan
4U type (rack-mounted type)
1
2
3
2
4
<Note>
1
Ensure that a temperature from 0 to 40 degrees Celsius is
maintained inside the rack.
Accessory parts:
3
Remove the eight blind screws from the BT-LH900 series.
(Refer to the instructions in the operation guide of the BT-LH900
series.)
Secure the main controls at bottom of the BT-LH900 series
monitor. (Refer to the instructions in the operation guide of the
BT-LH900 series.)
1 Remove the four screws and remove the rear panel.
2 Secure the monitor to the adapter using the four screws
provided.
Use the four screws to secure the rear panel.
8 screws for installing monitor
Bottom panel for 4U type (rack-mounted type)
2, 4
1
VQT0G64-2

Advertisement

loading

Summary of Contents for Panasonic BT-MA900G

  • Page 1 Installation Guide Rack mounting adapter for BT-LH900 series BT-MA900G The BT-MA900G rack mounting adapter is designed to be mounted on the model BT-LH900 series, a liquid crystal video monitor used in 2, 4 commercial applications, and make it possible to install this monitor in a standard 19-type rack.
  • Page 2 日本語 取付ガイド BT-LH900 シリーズ用ラックマウントアダプター BT-MA900G 2 、 4 BT-MA900G は、業務用映像液晶モニター BT-LH900 シ リーズに装着するラックマウントアダプターです。アダプタ ーを装着することで、BT-LH900 シリーズを 19 インチ標 準ラックに組み込むことが可能になります。 また、底板を付け替えることにより、モニターの上下チルト が可能な 5U タイプ(初期状態)をモニター固定式の 4U タ イプにすることが可能です。 < ノート > モニターの取り付けは、電源を切ってから行ってください。 底板の付け替えについて 1 右図を参照して計 12 本のビスを外します。 2 天板のビス 4 本をゆるめ、底板を外します。 3 付属品の底板と交換し、 1 で外したビスを使って止めま...