Ziegler 3410 Quick Start Manual

Ziegler mfm 3410 Ziegler mfm 3410
Digital Multifunction Instrument
Single Phase(1-PH)
Digital Volts, Amps & Frequency Indicator
Installati on & Operatin g Inst ructio ns
Section Conten ts
1. Introduction
2. Measurement Reading Screens
3. Programming
3.1 Password Protection
3.2 Set Up Screens
3.2.1 Potential Transformer Primary value
3.2.2 Current Transformer Primary value
3.2.3 Current Transformer Secondary value
3.2.4 Demand Integration Time
3.2.5 Demand Reset
4. Installation
4.1 EMC Installation Requirements
4.2 Case Dimensions and Panel Cut-out
4.3 Wiring
4.4 Auxiliary Supply
4.5 Fusing
4.6 Earth/ Ground Connections
5. Connection Diagrams
6. Specification
1. Introduction
The Instrument is a panel mounted 96x 96mm DIN Quadratic Digital
metering system for the measurement& display of basic electrical parameters like
AC Voltage, AC Current, Frequency, kVA, Ampere Demand and kVA Demand.
The instrument integrates accurate measurement technology (All
Voltage& Current measurements are True RMS upto 15th Harmonic) with3 line4
digits Ultra high brightness LED display.
The instrument can be configured and
x1000
SysV
programmed at site for the following: PT
Sys kVA
Primary, CT Primary, CT Secondary (5A or 1A)
SysA x1000
AD
kVAD
The front panel has two push buttons through
Hz x1000 which
Max AD
available measurement readings, reset the
Max kVAD
demand readings and configure the product.
Down
Up
TABL E 1:
Measure d Parameters
System Voltage
System Current
Frequency
System Apparent Power
Total System Current Demand
Total System kVA Demand
Maximum Total System Current Demand
Maximum Total System kVA Demand
15000500_Rev_A/09/09 E1.R0
the user may scroll through the
Uni ts of measurement
Volts
Amps
Hz
kVA
AD
kVAD
Max AD
Max kVAD
2. MeasurementRead ing Screens
In normal operation the user is presented with one of the measurement reading
screens out of available screens. These screens may be scrolled through one ata
time in incremental order by pressing the "
by pressing " Down key".
Screen 1: System screen
(System Voltage, System Current,
Frequency)
x1000
SysV
Sy s k VA
SysA
x1000
AD
kVAD
Hz x1000
Ma x AD
Ma x kVAD
Screen 2 : Ampere Demand
Max Ampere Demand
x1000
SysV
Sy s k VA
SysA
x1000
AD
kVAD
Hz x1000
Ma x AD
Ma x kVAD
Screen 3 : Apparent Power,
kVA demand and Max. kVA demand
SysV x1000
Sys kVA
SysA x1000
AD
kVAD
Hz x1000
Max AD
Max kVAD
3. Programming
The following sections comprise step by step procedures for configuring the
instrument for individual user requirements.
To access the set-up screens press and hold the"
Key simultaneously for5 seconds. This will take the User into the Password
Protection Entry Stage (Section 3.1).
3.1. Passwor d Protection
Password protection can be enabled to prevent unauthorised access to set-up
screens, by default password protection is not enabled.
Password protection is enabled by selectinga four digit number other than 0000,
setting a password of 0000 disables the password protection.
Enter Password, prompt for first digit.
(* Denotes that decimal point will be flashing).
SysV x1000
Sys kVA
Press the "
from0 through to 9, the value will wrap from 9 round to 0.
SysA
x1000
AD
kVAD
Press the "
Hz
x1000
In the special case where the Password is "0000" pressing
Max AD
the "
Max kVAD
advance to the "Password Confirmed" screen.
Enter Password, first digit entered, prompt for second digit.
(* Denotes that decimal point will be flashing).
SysV x1000
Sy s kVA
Press the "
digit from 0 through to 9, the value will wrap from9 round
SysA
x1000
to 0.
AD
kVAD
Press the "
Hz
x1000
Max AD
Max kVAD
www.ziegler-instruments.com
Up key" and in decremental order
Down" and " Up"
Down" key to scroll the value of the first digit
Up" key to advance to Up digit.
Up" key when prompted for the first digit will
Down" key to scroll the value of the second
Up" key to advance to Up digit.
1 | 6