Page 1
September 2021 The information contained in this document is of commercial value, proprietary to Telrad Networks. It is conveyed to the recipient solely for the purpose of evaluation. Reproduction of this document, disclosure of its contents or any other use of the information herein is strictly forbidden unless expressly authorized in writing by Telrad Networks.
Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial liabilities. Telrad Networks and its resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas.
Page 3
Telrad Networks’s control. Telrad Networks will not be responsible for any loss, damage or injury arising directly or indirectly from the use of this product. Telrad Networks’s total liability under the terms of this warranty shall in all circumstances be limited to the replacement value of this product.
Telrad Networks Ltd. BreezeAIR Installation Guide Thank you for purchasing BreezeAIR solution. Telrad Networks's BreezeAIR series is a carrier-grade point-to-point and Point-to-multipoint broadband wireless solution that sets a benchmark of unrivaled performance, reliability, capacity, latency and RF robustness, making it the ultimate choice for future-proof wireless system.
Telrad Networks Ltd. BreezeAIR Installation Guide When you first open the package, verify that the unit is complete with the following components: 1. Outdoor Unit – BreezeAIR MU or SU. 2. Indoor PoE power supply. 3. Pole mounting kit (will not be added for units that require advanced mounting kit).
Failure to do so may void the product warranty and may expose the end user or the service provider to legal and financial liabilities. Telrad Networks and its resellers or distributors of this equipment are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas.
Telrad Networks Ltd. BreezeAIR Installation Guide 4) Connect the Outdoor-to-Indoor shielded CAT5 cable to the Outdoor unit and route it to the selected location of the PoE. Assemble the enclosed connector on the cable. 5) Mount the Indoor POE and connect: ...
Telrad Networks Ltd. BreezeAIR Installation Guide Note: A distance of at least 250cm between the equipment and all persons should be maintained during the operation of the equipment. Une distance d'au moins 250cm entre l'équipement et toutes les personnes devraient être maintenues pendant le fonctionnement de l'équipement...
Telrad Networks Ltd. BreezeAIR Installation Guide BreezeAIR advanced mounting kit features: Azimuth and Elevation Adjustable Mount Suitable for pole or wall mounting Made of Die Cast Aluminum Heavy duty Packing list Item Description MK1 (End Mounting Member)
Telrad Networks Ltd. BreezeAIR Installation Guide BreezeAIR system supports two types of antennas: Integrated antenna External antenna Selecting the antenna model is according to the required range and performance. Note: To comply with the regulation EIRP limits, the outdoor unit-transmit power needs to be adjusted according to the installed antenna gain.
Page 13
BreezeAIR Installation Guide FCC - 5.8 GHz IMPORTANT! Antennas must be selected from a list of Telrad Networks approved antennas. Please refer to Appendix C – FCC approved antennas. It is the responsibility of the installer to ensure that when using the outdoor antenna kits in the United States (or where FCC rules apply), only those antennas certified with the product are used.
Page 14
Telrad Networks Ltd. BreezeAIR Installation Guide (2) High power point-to-point and point-to-multipoint operations (both fixed and temporary- fixed rapid deployment) may employ transmitting antennas with directional gain up to 26 dBi without any corresponding reduction in the maximum conducted output power or spectral density.
Telrad Networks Ltd. BreezeAIR Installation Guide Power up the unit: 1. Plug the Power Supply into a wall outlet or other standard AC power source. This is only for use prior to permanent mounting, so any available wall outlet in close proximity to your mounting location is suitable.
Telrad Networks Ltd. BreezeAIR Installation Guide 3. Take the unit to the selected location and align the antenna in the link’s direction. Listen to the buzzer tone level. Any sound (fast, medium or slow) indicates a reception. 4. Change and rotate the antenna to the left, right, up and down, scanning for the maximum reception point.
Telrad Networks Ltd. BreezeAIR Installation Guide The outdoor unit is connected to straight CAT5 Gauge 24-shielded outdoor rated cable. The cable should be UV resistant, flame retardant, UL listed and contain at least 4 twisted pairs. – The outdoor cables scheme is indicated in Appendix A Outdoor Cables Scheme.
Telrad Networks Ltd. BreezeAIR Installation Guide The indoor PoE is assembled as follows: 1. Crimp the RJ-45 Plugs on cable ends to form the Outdoor Unit cable. 2. Plug the Outdoor Unit cable to the RJ-45 Jack marked “PWR LAN-OUT”.
Telrad Networks Ltd. BreezeAIR Installation Guide The outdoor unit shall be connected to a protective earth with not less than 10 AWG conductors having green-yellow insulation. The following figure shows the grounding cable from outdoor unit external screw to adjacent grounding rod. The cable should be long enough to reach from the mounting pole to the grounding rod with 3 to 6 feet extra to allow for strain relief.
Any unauthorized modification or changes to this device without the express approval of Telrad Networks may void the user’s authority to operate this device. Furthermore, this device intended to be used only when installed in accordance with the instructions outlined in this manual.
Telrad Networks Ltd. BreezeAIR Installation Guide BreezeAIR is designed to work with co-located radios. This means that two or more units can be mounted close to each other. Time synchronization allows reusing frequencies between co-located links and configured with the Link Manager advanced window.
Telrad Networks Ltd. BreezeAIR Installation Guide Radio BreezeAIR ACE BreezeAIR 8000 MIMO BreezeAIR 8000 SISO Radio Frequency 4.8-6.1GHz 700MHz, 900MHz, 2.0-2.3GHz, 2.3-2.7GHz, 3.3-3.8GHz, 4.4- 4.8GHz, 4.8-6.0GHz, 6.0-7.0GHz, 7.0-8.0GHz, 10.0-10.7GHz Net Throughput 2x2 – up to 750Mbps Up to 310Mbps Up to 150Mbps [ET model –...
Telrad Networks Ltd. BreezeAIR Installation Guide – – Figure 5-1: Outdoor Cables Scheme Note: In order to comply with 100 meter CAT5 cable Pins 1,2 must be a twisted pair wire. Pins 3,6 must be a twisted pair wire.
Telrad Networks Ltd. BreezeAIR Installation Guide – – All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced current from a near strike. A direct lightning strike may cause serious damage even if these guidelines are followed. Lightning protection and grounding practices in local and national electrical codes serve to minimize equipment damage, service outages, and serious injury.
Telrad Networks Ltd. BreezeAIR Installation Guide Telrad Networks BreezeGuard is 1000Mbps PoE Outdoor Surge Protector, is designed to protect BreezeAIR PoE network from lightning over-voltage, transient over-voltage and static discharge. The protector implements multi-level protection circuit with advanced manufacturing process, and has excellent performance on discharge current, limiting voltage, response time, stability and over-all reliability.
Need help?
Do you have a question about the BreezeAIR ACE and is the answer not in the manual?
Questions and answers