便携式音箱 二、手持麦克风 ① ② ③ ④ ① 液晶显示屏:显示频率、麦克风信号、电池电量等信息; ② 电源按键:长按3秒开启或关闭麦克风;循环点按此键调节麦克风音量,分为 (U08-U11)共4级音量,调节麦克风音量时音箱会同时发出“滴”的一声提示音; ③“HI/LQ”按键:用于对频操作,详见本说明书“对频方法”部分; ④ 电池仓:装入2节1.5V AA电池。 麦克风显示屏 1. 电池电量:电池电量有三格,以格数表示电池电量,电量不足时,电池符号闪烁, 请及时更换电池; 2. 信号符号:“ ”表示麦克风信号;...
■ Product Dear customer, Thank you for purchasing WDA-500 portable speaker. Please read the manual carefully before operation and keep it for reference in future. If you have any question, please contact the local dealer. ■ Features Handheld version The portable multifunction speaker, suitable for outdoor performance, square ●...
Charging: USB 5V 200mA (0db=1V/Pa/m at 1kHz) Charging Time: approximate 2.5h UHF Frequency: 650MHz~670MHz Operation Time: approximate 5h (segmented) Net Weight: approximate 39g Note: the above data are measured by Takstar laboratory and Takstar has the right of final interpretation.
■ Function instruction A. Speaker Front panel function ⑭ ⑫ ⑬ ③ ⑮ ⑯ ⑰ ⑱ ⑲ ⑳ INPUT OUTPUT MIC DC 12V 1A ⑨ ⑧ ⑦ ⑩ ⑤ ⑥ ④ ② ① ⑪ ① Power switch: keep pressing it for 2 seconds to turn on/off the speaker. After turning on, LED screen displays UHF symbol.
Page 25
⑤ Previous song button: press it for previous song. In radio mode, press it for previous channel. ⑥ Next song button: press it for next song. In radio mode, press it for next channel. ⑦ Repeat button: in TF card/USB mode and playing music, press it to switching repeat single or all music playing.
Page 26
LED screen 1. Turning on symbol: after turning on, it displays UHF symbol. Refer to figure ①. 2. “ ”battery power: when the power is sufficient, it does not display the symbol. When insufficient, the symbol flashes, and it has the sound prompt “insufficient power, please charge”.
Page 27
5. Mic symbol: when mic is connected, it displays MIC symbol. When disconnected, the symbol disappears. Refer to figure ⑦. 6. Play/pause symbol: during music playing, it displays“00:00”changing. When the music is paused, it displays “PAUS”. Refer to figure ⑧. 7.
B. Microphone ① ② ③ ④ ① LCD: displaying frequency, mic signal, battery power, etc; ② Power switch: keep pressing it for 3 seconds to turn on/off the microphone. Press it to adjust mic volume (U08-U11), totally four levels. When adjusting mic volume, the speaker has sound prompt.
3. Frequency information: displaying the current mic operation frequency, (650MHz~670MHz)15 frequencies in all. During fr equency matching, it flashes. 4. Volume information: when mic volume is adjusted, the screen displays“U 00”. This means the mic volume level. After 3 seconds, it displays the frequency information.
⑥ Charging interface: Connect to the USB data cable. Please use a charging head with a specification of 5V 1A and 3C certification to charge the amplifier. ⑦ Power indicator: When the microphone is turned off and not charging, the indicator lights off;...
① Button: switching operation mode. Refer to the panel mode section for Details. ② Ducking button: turning on/off ducking function. Refer to the ducking section for details. ③ Recording button: turning on/off recording function. Refer to the recording section for details. ④...
Mic connector B. Holding microphone correctly 1. Put the mic away from you mouth in a range 5~15cm. Too close range leads to distortion due to over-modulation. Too far range decreases S/N ratio due to less modulation. 2. Hold the middle part of microphone. Do not hold the mic grille to avoid feedback. Do not hold the mic tail part to avoid affecting mic signal.
90° Audio source Speaker 90° C. Connecting with cell phone/PC/mixer/sound card Connect one end of Φ3.5mm audio cable with Φ3.5mm connector of speaker, and the other end with the output connector of cell phone/PC/sound card. If the cell phone has no Φ3.5mm connector, use OTG adapter (buy additionally. Refer to the figure: Audio input Cell...
D. Serial connection WDA-500 supports serial connection for multiple speaker reinforcement simultaneously. Link the out connector of the first speaker with the in connector of the second one via Φ3.5mm audio cable. Audio input Audio output The current operating one The second one E.
M button of the microphone for 3 seconds until the blue light blinks rapidly. At this point, immediately turn on the WDA-500 speaker to start frequency pairing. If the speaker is not turned on within 10 seconds, the pairing will fail.
3. During charging, it displays the power symbol. This means it is being charged. When the power symbol disappears, this means it is being charged fully. 4. Please use standard power adapter to charge WDA-500. It takes about 4h. When it is charged fully, please stop the charging.
■ Caution To avoid electric shock, over temperature, catching fire, explosion, mechanical risk and hurt or property loss caused by improper use, please read the following items carefully before operation: 1. Please check if the power of the connected equipment matches with that of this product before operation.
Waste Management Bureau or household waste treatment service. ■ About the user manual For more information, please visit our website: https://www.takstar.com/. Takstar reserves the final interpretation right!
Need help?
Do you have a question about the WDA-500 and is the answer not in the manual?
Questions and answers