Sealey OS400 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. SAFETY
i
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. This power tool is intended to function as a sander. Operations such as
‰
grinding, wire brushing, polishing or cutting off are not recommended to be performed with this power tool.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
sander.
Save all warnings and instructions for future reference.
9
DO NOT use accessories which are not specifically designed and recommended by the tool manufacturer.
8
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool.
9
The outside diameter and the thickness of the accessory must be within the capacity rating of your power tool.
9
Threaded mounting of accessories must match the sander's thread.
9
DO NOT use a damaged accessory. Inspect accessories before each use. If the tool or accessory is dropped, inspect for damage.
8
After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run
9
the power tool at maximum no-load speed for one minute.
1.3. WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
9
DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
8
create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
9
1.4. PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a power tool. DO NOT use a power tool while you are
9
tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious
personal injury.
Wear personal protective equipment.
9
© Jack Sealey Limited
Ø150MM RANDOM ORBITAL ELECTRIC SANDER
600W
OS400
MODEL NO:
Wear eye Wear face
protection mask
Original Language Version
Wear ear Keep tool dry
protection
Recommended
fuse rating: 13A
OS400 Issue:2 (F) 20/10/21