Table of Contents
Advertisement
Quick Links
Giter Co., Ltd.
808-812, Building 10A, Zilang Science and Technology City, 60 Chongzhou Avenue,
Economic and Technological Development Zone, Nantong，Jiangsu Province, 226006
T
+86 512 6828 7609
E
info@giter-ess.com
W
www.giter-ess.com
INSTALLATION MANUAL
BATTERY MODULE
G2500-48
G2500-24
Version：V5.0
Advertisement
Table of Contents
Related Manuals for GITER G2500-48
Summary of Contents for GITER G2500-48
- Page 1 INSTALLATION MANUAL BATTERY MODULE G2500-48 G2500-24 Giter Co., Ltd. 808-812, Building 10A, Zilang Science and Technology City, 60 Chongzhou Avenue, Economic and Technological Development Zone, Nantong，Jiangsu Province, 226006 +86 512 6828 7609 Version：V5.0 info@giter-ess.com www.giter-ess.com...
-
Page 2: Copyright Statement
CONTENT Copyright Statement This manual is under the copyright of GITER Co., Ltd, with all rights reserved. Please keep the 1. Introduction manual properly and operate in strict accordance with all safety and operating instructions in this 1.1 General Precaution manual. - Page 3 Check the following parts list and make sure there is no part missing. battery fire ex-tinguishers that meet the national requirements to put out the fire. GITER delivers a complete system including: 6.If the battery is improperly lifted or dropped while being removed during transportation, it can GTE Battery cause injury.
- Page 4 2.2.2 Interface 2.2.2 Error and Protection Code LED Light Protection Code LED Display Description Temperature difference High temperature Figure 1 G2500-48 Interface Discharging in low-temperature environment Item Description Item Description Green light flashes every 3 Earthing point(with screws) (x2) Power Switch Over-current charge seconds.
-
Page 5: Error Code
Error Code: 2.3 Limitation of Liability Any product damage or property loss caused by the following conditions Giter does not assume any Error Code LED Display Description Troubleshooting LED Light direct or indirect liability. Product modified, design changed or parts replaced without Giter authorization;... - Page 6 Figure 4 Install battery module & connect copper bar 1. Ensure that the power button of all batteries is OFF; (Take G2500-48 as an example) 2. Cut off all relevant power supply. Step 2: As shown in Figure 4, put the battery into the cabinet, tighten the four-angle screws (M6*12 cross head triad screw, torque: 5 N.m);...
- Page 7 （Accessories need to be purchased separately） Figure 9 Stack and install 6 batteries (Take G2500-48 as an example) Step3: Refer to Step 2 and stack the battery in turn, as shown in Figure 9。 Figure 7 Install the first battery Step 1: As shown in Figure 7, place the battery on the base and tighten limit brackets located at the four corners (screw: M4*10 outer hexagonal and internal torx combination screw;...
-
Page 8: System Operation
2.4.3.3 Communication Connection Diagrams START: Switch off the Battery Breaker, press the Power Switch (Rebound button) to "ON" for 1-2 seconds. Then the battery module will activate and the LED display will light up. CLOSE: Press the Power Switch (Rebound button) to "ON" for 5 seconds, and the bat-tery will be turned off. -
Page 9: Specification
5. Appendix 4. Check if the ambient temperature is within the 5.1 Specification operating range; 5. Disconnect the power ca-bles Items G2500-48 G2500-24 and test the battery output voltage. If the voltage is too low, Nominal Voltage 51.2V 25.6V please charge immediately. If...
Need help?
Do you have a question about the G2500-48 and is the answer not in the manual?
Questions and answers