Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Brooks Manuals
  4. Control Panel
  5. firetracker FT1020G3 FDCIE
  6. Quick operation manual

Brooks FIRETRACKER FT1020G3 Quick Operation Manual

Hide thumbs Also See for FIRETRACKER FT1020G3:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
FIRETRACKER FT1020G3 - QUICK OPERATION
1 - TO SILENCE PANEL BUZZER:
Press
Button once to silence panel buzzer.
2 -TO SILENCE ALARM DEVICES:
Press
Button once to silence all alarm devices, Occupant Warning System
(OWS) or sounders and wait for a few seconds.
Pressing the
3 - TO RESET FIRE ALARM:
IMPORTANT: Alarm devices must be silenced before pressing "Reset" button.
Press and hold the
reset sequence. The system will now automatically reset all alarms.
Alarms may re-trigger in the system if the alarm condition is still present. Wait for 30 seconds
and try again.
4 - TO DISABLE (ISOLATE) AN ACTIVE ALARM:
IMPORTANT: Alarm devices must be silenced before pressing "Disable" button.
Button to isolate device in alarm (H2/B1) – system will now illuminate
Press
the
manual re-enabled via Menu H2/B1 button.
FT1020G3 Quick Operation Guide
Button again will cause the alarms to resound.
Button for 1 second until the Fire Alarm Panel starts its
LED. This zone / address point will remain disabled until
GUIDE
2022/01/06
Page 1 of 6

Advertisement

loading

Related Manuals for Brooks FIRETRACKER FT1020G3

Summary of Contents for Brooks FIRETRACKER FT1020G3

  • Page 1 2022/01/06 FIRETRACKER FT1020G3 - QUICK OPERATION GUIDE 1 - TO SILENCE PANEL BUZZER: Press Button once to silence panel buzzer. 2 -TO SILENCE ALARM DEVICES: Press Button once to silence all alarm devices, Occupant Warning System (OWS) or sounders and wait for a few seconds.
  • Page 2 2022/01/06 5 - TO DISPLAY MORE THAN ONE ALARM : When the more than one alarm are queued, red LEDs are illuminated. Press the Button to see the additional Alarms. 6 - TO MANUALLY DISABLE (ISOLATE) A ZONE OR ZONE ADDRESS FROM THE MENU: 1.
  • Page 3 2022/01/06 7 - MANUALLY RE-ENABLE A ZONE OR ZONE ADDRESS FROM THE MENU: 1. Press Menu Button 2. Select “Building Officer” Login then Key Enter Access Code. 3. Scroll to the Disable or re-enable menu (H2) by pressing Button/s then press Accept 4.
  • Page 4 2022/01/06 10 – TO ACKNOWLEDGE FAULT 1. Press Menu Button 2. Select “Building Officer” Login then Key Enter Access Code. 3. Scroll to the FAULT ACKNOWLEDGE menu (H6) by pressing Button/s then press to Accept 4. Scroll to check the list of faults by pressing Button/s then press to Accept 5.
  • Page 5 2022/01/06 FAULT: L-C mixed COM loop x, Control Unit xx Page: 66 FAULT: Loop unit, Technical number xxxxxx Page: 66 FAULT: Loop unit zone: xxx address: xx Page: 66 FAULT: Loop unit zone: xxx address: xx and zone: yyy address:yy Page: 66 FAULT: Low battery capacity, Control Unit xx Page: 66...
  • Page 6 2022/01/06 13 – OPERATION MANUAL FT1020G3 Rev 2.4 Scan QR code to Search instructions and other relevant operational procedures. Software download Restart Perform Monthly test (H1) Disable or re-enable (H2) Set Calendar and Clock (H3) Present System Status (H4) Service (H5) Acknowledge Faults (H6) Perform Zone Test (Test Mode) (H7) Maintenance (H8)