Subscribe to Our Youtube Channel
Related Manuals for MKS ESP302-GPIB-ADPT
Summary of Contents for MKS ESP302-GPIB-ADPT
- Page 1 A1387A User's Manual ESP302-GPIB-ADPT ESP302 GPIB to Serial Adaptor FAX: +1 (949)-253-1680 1771 Deere Avenue Irvine, CA 92606 United States WWW.NEWPORT.COM +1 (949)-863-3144...
- Page 2 MKS Instruments, Inc. This document is provided for information only, and product specifications are subject to change without notice.
-
Page 3: Table Of Contents
2.5.2 Data Character Format ..................... 14 2.5.3 RS-232 Specifications ....................... 14 2.5.4 Flow Control ........................14 2.5.5 Parity Generation/Checking ....................14 Indicators ..........................15 Physical characteristics ......................16 3 Installation ............................17 Unpacking ..........................17 Shipment verification ........................ 17 3 | ESP302-GPIB-ADPT... - Page 4 Important note to former ESP301 controller users..............23 5 Maintenance ............................24 Maintenance ..........................24 Troubleshooting ........................24 Repair ............................24 6 Appendix ............................25 Self-Test Error Codes ......................25 ERR LED Error codes ......................26 Service Form ............................27 4 | ESP302-GPIB-ADPT...
-
Page 5: List Of Figures And Tables
Figure 3: GPIB connector J2 ........................17 Figure 4: RS-232 Serial connector J1 ....................18 Figure 5: PWR input ..........................19 Figure 6: ESP302-GPIB-ADPT GPIB Port Connection ................19 Figure 7: LEDs ............................20 Table 1: Characteristics .......................... 16 Table 2: J1 RS-232 Signal-Pin Assignments ..................18 Table 3: ESP302-GPIB-ADPT Self-Test Error Codes ................ -
Page 6: Warranty
MKS Instruments, Inc. warrants that this product will be free from defects in material and workmanship and will comply with MKS published specifications at the time of sale for a period of one year from date of shipment. If found to be defective during the warranty period, the product will either be repaired or replaced at MKS option. -
Page 7: Eu Declaration Of Conformity
USER's MANUAL A1387A0-EDH0429En1010 11/21 EU Declaration of Conformity 7 | ESP302-GPIB-ADPT... -
Page 8: Declaration Of Conformity
USER's MANUAL A1387A0-EDH0429En1010 11/21 UK Declaration of Conformity 8 | ESP302-GPIB-ADPT... -
Page 9: Preface
Customer shall protect the MKS Instruments, Inc. Programs and Related Materials as trade secrets of MKS and shall devote its best efforts to ensure that all its personnel protect the MKS Programs as trade secrets of MKS. Customer shall not at any time disclose MKS trade secrets to any other person, firm, organization, or employee that does not need (consistent with Customer's right of use hereunder) to obtain access to the MKS Programs and Related Materials. -
Page 10: Safety Information
DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT Do not install substitute parts or perform any unauthorized modification to the instrument. Return the instrument to an MKS l Newport Service Center for service and repair to ensure that all safety features are maintained. -
Page 11: Symbols Found On The Unit
For information about where the user can drop off the waste equipment for recycling, please contact your local MKS l Newport representative. 1.4 Cautions This product is a Class A device. In a residential environment, this CAUTION device can cause electromagnetic interference. -
Page 12: Description
This manual provides operating instructions for the ESP302-GPIB-ADPT that you have purchased. ESP302-GPIB-ADPT The ESP302-GPIB-ADPT is a "GPIB to Serial Adaptor" especially dedicated to connecting Newport ESP302 Motion Controller (equipped with a serial port) to a GPIB bus for users who want to drive it with an IEEE 488 interface. -
Page 13: Protection Of Configuration Parameters
GPIB port configuration only (see §3.5) The ESP302-GPIB-ADPT powers up in the Data mode and switches to the Command mode when sent a GPIB Device Trigger (488.1 GET) command. Once in the Command mode, the unit will accept configuration parameters, respond to queries, and save new configuration settings but not transfer serial data. -
Page 14: Serial Interface
USER's MANUAL A1387A0-EDH0429En1010 11/21 2.5 Serial Interface The ESP302-GPIB-ADPT provides RS-232 signals on a rear panel DE-9P male connector. The choice of serial signals is selected by internal jumpers and factory settings. Signal pinouts are listed in Table 2.5.1 Baud Rate Baud rate 19200 baud. -
Page 15: Indicators
Refer to paragraph 6.1 for a description of the errors and their possible causes. If the 5-volt reading is below 4.7 volts, the ESP302-GPIB-ADPT will repeat its power turn-on sequence until the voltage level reaches 4.8 volts or higher. -
Page 16: Physical Characteristics
USER's MANUAL A1387A0-EDH0429En1010 11/21 2.7 Physical characteristics The ESP302-GPIB-ADPT is packaged in a small metal case that can be used on the bench top or panel mounted. Table 1: Characteristics 6.11" L x 3.89" W x 1.13" H Size (15.52 cm L x 9.88 cm W x 2.87 cm H) Weight 1 lbs. -
Page 17: Installation
3.4 CONNECTIONS 3.4.1 GPIB Interface and Connector J2 The ESP302-GPIB-ADPT has a standard 24-pin, female GPIB connector with metric lock studs that accepts stacked and straight-in GPIB connectors. Use any GPIB cable to connect your GPIB controller to the ESP302-GPIB-ADPT. -
Page 18: Serial Interface And Connector J1
Optional power input/output (not used) Figure 5: RS-232 Serial connector J1 Use the special serial cable to connect the ESP302-GPIB-ADPT module to the ESP302 port. For custom cables check the cable connections to assure that the transmit data from the ESP302 pin 2 connects to the ESP302-GPIB-ADPT receive data input pin 2. -
Page 19: Gpib Port Configuration
Newport ESP302 controller from a GPIB. If necessary, only the ESP302-GPIB-ADPT GPIB address can be changed from the GPIB port. interface (if satisfied with default GPIB address 4, you can skip to section 4) GPIB address configuration requires an interactive program that can: •... -
Page 20: Starting Communication
Read: NEWPORT, ESP302-GPIB-ADPT, S/N 501001, rev x1 (example) • If you do not get a response, power the ESP302-GPIB-ADPT off and repeat this sequence until you can read the IDN message. • If the ESP302-GPIB-ADPT’s red ERR LED comes on, send an *ESR? query to clear the error. -
Page 21: Gpib Address Setting
Send the following SCPI command to set a different GPIB address (5 for instance): Write: SYST:COMM:GPIB:ADDR 5 • To query the address setting, add a question mark, ‘?’, to the SCPI command and send it to the ESP302-GPIB-ADPT module. The response should display the new address value: Write: SYST:COMM:GPIB:ADDR? Read: •... -
Page 22: Operation
Data mode. 4.2 Operation with the ESP302 controller Once the ESP302-GPIB-ADPT is connected to a Newport ESP302 controller, and if in Data mode (which is the case upon start-up), user can send specific commands to the ESP302 (see ESP302... -
Page 23: Important Note To Former Esp301 Controller Users
As mentioned above, ESP302 messages terminate by CR+CR+LF instead of CR+LF. • ESP301 "SA" command should be replaced by the previously described procedure to set the GPIB address. Basically, the GPIB address is set in the ESP302-GPIB-ADPT and not in the ESP302. •... -
Page 24: Maintenance
5 Maintenance 5.1 Maintenance The ESP302-GPIB-ADPT does not require periodic calibration and has no internal adjustments. However, if it is used in an application where the IEEE-488 bus cables are frequently changed, the ESP302-GPIB-ADPT's IEEE-488 Bus Connector may occasionally require cleaning to remove wax and dirt buildup. -
Page 25: Appendix
6 Appendix 6.1 Self-Test Error Codes At power turn on, the ESP302-GPIB-ADPT conducts a self-test of its major components. A successful test ends when the RDY LED on. Test failures are indicated by the LED patterns shown in Table below. Typically, the failure is a pattern of blinking LEDs which lasts for 5 seconds. If the ESP302- GPIB-ADPT does not have a fatal error, the self-test will continue until it is complete but the RDY LED will remain off. -
Page 26: Err Led Error Codes
Memory Setup variable data corrupted. Query Query error, data not read or read attempted with no data present. Timeout GPIB Bus timeout. Operation Complete. Operation Complete has no meaning in the Adaptor and is always 0. 26 | ESP302-GPIB-ADPT... -
Page 27: Service Form
Item(s) Being Returned: _______________________________ Model#: ___________________________________________ Serial #: ___________________________ Description: _____________________________________________________________________________ Reasons of return of goods (please list any specific problems): _____________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ _______________________________________________________________________________________ 27 | ESP302-GPIB-ADPT... - Page 28 Visit MKS l Newport Online at: www.newport.com North America & Asia Europe Newport Corporation MICRO-CONTROLE Spectra-Physics S.A.S 1791 Deere Ave. 7 rue des Plantes Irvine, CA 92606, USA 45340 Beaune-la-Rolande France Sales Sales Europe (EMEAI) Tel.: +1 (949)-863-3144 e-mail: sales@newport.com Tel.: +49 (0) 6151-708-0...
Need help?
Do you have a question about the ESP302-GPIB-ADPT and is the answer not in the manual?
Questions and answers