Page 1
LCD TV SERVICE MANUAL CHASSIS : LP62D FACTORY MODEL : 42LC2RH-ZH MODEL : 42LC2RH CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Page 4
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range 3. Test method This specification is applied to LP62D chassis. 3.1 Performance : LGE TV test method followed 2. Requirement for Test 3.2 Demanded other specification Safety : CE, IEC Specification Testing for standard of each part must be followed in below EMC : CE, IEC...
Page 7
5. General Specification Item Specification Remark Panel 42" TFT WXGA LCD Frequency range H : 31 ~ 61KhzV : 56 ~ 75Hz PC Input Control Function 1) Contrast/Brightness 2) H-Position / V-Position 3) Tracking : Clock / Phase 4) Auto Configure 5) Reset Component Jack Y/Pb/Pr : 1EA...
Page 8
7. Model Specification Item Specification Remark Market Broadcasting system PAL BG/I/DK, SECAM Available Channel BAND VHF/UHF C1 ~ C69 CATV S1 ~ S47 Receiving system Upper Heterodyne SCART Jack(2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60 Video Input (2EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60...
Page 9
8. Component Video Input (Y, PB, PR) Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Remarks 720 x 480 15.73 59.94 13.500 SDTV, DVD 480I(525I) 720 x 480 15.75 60.00 13.514 SDTV, DVD 480I(525I) 720 x 576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 720 x 480 31.47 59.94...
Page 10
11. HDMI Input ( PC ) Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Remarks 720 x 400 31.469 70.08 28.32 640 x 480 31.469 59.94 25.17 VESA(VGA) 640 x 480 37.500 75.00 31.50 VESA(VGA) 800 x 600 37.879 60.31 40.00 VESA(SVGA) 800 x 600 46.875 75.00 49.50...
• Auto Component Color Balance adjustment Model Name - Standard equipment : MSPG925FA 42LC2RH-ZH 00 00 00 FC 00 34 32 4C 43 32 52 2D 48 4D 48 0A 20 20 • Auto RGB Color Balance adjustment e. Checksum: Changeable by total EDID data...
Page 12
5. ADC Calibration 5.1 Adjustment of RF/AV/S-VIDEO * Required Equipments • Remote controller for adjustment • 802F Pattern Generator, Master (MSPG-925FA), etc. • MSPG-925FA Pattern Generator (Which has Video Signal: 100% Color Bar Pattern shown in Fig. 1) (Fig. 2) = >...
Page 13
6. White Balance 6.2 Auto white Balance (AV) 1) LPL Module White balance ZH(AV3), TH(AV1) MH(VIDEO1) Data MSPG925FA 216 Level (85IRE) Model : 202 Model : 201 Command1 Command2 Set ID Full screen pattern • Pal Video • NTSC Video Input Select R-Gain =>...
Page 14
7. Shipping Conditions Item Condition Remark Power Volume Level Main Picture Input Main Last Channel Pr 01 Mute 16 : 9 Station Auto Programme Manual Programme Programme Edit Favorite Programme None Picture Dynamic Dynamic Contrast Brightness Colour Sharpness Normal Auto Advanced Reset Sound...
Page 15
SVC REMOCON FUNTION REAMARK To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)
Need help?
Do you have a question about the 42LC2RH and is the answer not in the manual?
Questions and answers