Download Print this page
Sealey AP2200BB.V2 Series Instructions

Sealey AP2200BB.V2 Series Instructions

6 drawer topchest & rollcab combination with ball-bearing slides

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
Refer to
instruction
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
Topchest & Rollcab combination.
Locate the Topchest & Rollcab combination in a suitable working area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the Topchest & Rollcab combination clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the Topchest & Rollcab combination for any purpose other than that for which it is designed.
8
DO NOT move the Topchest & Rollcab combination with drawers open.
8
DO NOT open more than one drawer at the same time.
8
DO NOT step on the drawers.
8
DO NOT use in damp work areas.
8
WARNING! The warnings, cautions and instructions referred to in this instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied
by the operator.
2. INTRODUCTION
i
The economical way to buy American PRO® Ball-Bearing quality tool chests. Supplied packed one inside the other. This mid-size combo has
smooth 25mm ball-bearing slides and all the features of the professional chests, except that the rollcab is not lockable and the castors are Ø75mm.
These boxes are not interchangeable with the rest of the American PRO® Ball-Bearing Range.
3. SPECIFICATION/FIXINGS
Specification (W x D x H):
4 DRAWER TOPCHEST:
Overall Size:
Small Drawer (x3):
Medium Drawer (x1):
2 DRAWER ROLLCAB:
Overall Size:
Medium Drawer (x2):
Cupboard (x1)
4. ASSEMBLY
4.1.
Remove the bolts, nuts and washers from the base of the rollcab (fig.1), and then lift off the body to uncover the topchest.
4.2.
Remove the screws from the base (fig.2), and separate from the topchest, discard the screws.
NOTE: Place protective material onto the ground to avoid damaging the back of the topchest.
4.3.
Turn the rollcab upside down and place the base into position as shown in fig.3A.
NOTE: Place protective material onto the ground to avoid damaging the top of the rollcab.
4.4.
Position the corner brackets (fig.3B) and secure using bolts, washers and nuts.
4.5.
Attach the back panel to the base using two bolts, washers and nuts.
4.6.
Ensure the base is square in the rollcab and tighten all nuts fully (fig.3C).
4.7.
Place the rollcab upright and place the topchest on top as shown in fig.4.
© Jack Sealey Limited
6 DRAWER TOPCHEST & ROLLCAB COMBINATION
WITH BALL-BEARING SLIDES
MODEL NO:
600 x 260 x 340mm
510 x 225 x 35mm
510 x 225 x 85mm
615 x 295 x 705mm
515 x 275 x 65mm
610 x 275 x 375mm
Original Language Version
AP2200BB.V2 SERIES
FIXINGS
AP2200BB.V2 Series Issue 2 (H) 19/05/22

Advertisement

loading

Summary of Contents for Sealey AP2200BB.V2 Series

  • Page 1 AP2200BB.V2 SERIES MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product.