Download Print this page

BE AgriEase -23MS Operation Manual

Manure spreader

Advertisement

Quick Links

MANURE SPREADER
BE-XXMS
OPERATIONS & PARTS MANUAL
FOR MODELS:
• BE-23MS
• BE-32MS
PURCHASE DATE
MODEL NO.
SERIAL NUMBER
DEALER

Advertisement

loading
Need help?

Need help?

Do you have a question about the AgriEase BE-23MS and is the answer not in the manual?

Questions and answers

Summary of Contents for BE AgriEase BE-23MS

  • Page 1 MANURE SPREADER BE-XXMS OPERATIONS & PARTS MANUAL FOR MODELS: • BE-23MS • BE-32MS PURCHASE DATE MODEL NO. SERIAL NUMBER DEALER...
  • Page 2 TABLE OF CONTENTS INTRODUCTION OPERATION MAINTENANCE & ADJUSTMENT APPENDIX EXPLODED VIEW & PARTS LIST...
  • Page 3 DANGER! The utmost levels of safety must be observed; an extreme hazard exists which would result in high probability of death or irreparable serious personal injury if proper precautions are not taken. The best operator is a careful operator. Use common sense and observe general safety rules.
  • Page 4 (e.g. ATTENTION, CAUTION, WARNING, DANGER). For your safety and the safe operation of your equipment, review all labels and heed all safety messages as printed on the labels. Be sure to keep the safety labels clean and readable. If the labels ever become damaged or illegible, contact Braber Equipment for replacements.
  • Page 5 • The jack stand dolly wheel option allows easy movement of the spreader around the stable or bam; also adjusts the height of the spreader to facilitate hook-up to the spreader towing vehicle. • The end gate helps to contain loads between spreading and also shields the operator during spreading. BE-XXMS USER MANUAL...
  • Page 6 For operation in the field, the Agriease spreaders can be towed by a number of vehicles such as garden For operation in the field, the Agriease spreaders can be towed by a number of vehicles such as garden tractors, ATVs, tractors, ATVs, and utility vehicles.
  • Page 7 If your spreader is equipped with a manual end gate, return the end gate to the closed (down) position. Refer to Section 3 in this manual for maintenance to be performed following operation of the spreader. BE-XXMS USER MANUAL...
  • Page 8 IMPORTANT! After a few hours of initial operation, watch and listen for any loose components. Be aware that it may be necessary to re-tighten hitch hardware and/or wheel bolts: please refer to Section 3 in this manual for the proper torque specifications.
  • Page 9 The spreader should be greased every 50 loads or once a month. Wipe the old grease and any dirt or dust off the grease fittings before greasing so it doesn’t get forced into the bearing.
  • Page 10 There is one grease fitting on each axle bearing. Figure 8 There is one grease fitting on each rear web bearing. Figure 7 Revision06/2017 Figure 8 Figure 9 There is one grease fitting on each beater bearing. BE-XXMS USER MANUAL Figure 9 Figure 10...
  • Page 11 Lubricate the beater drive chain with engine oil every Figure 11 50 loads or once a month. Lubricate the beater drive chain with engine oil every 50 loads or once a month. Figure Figure Farmer-Helper 25 & 27G Revision06/2017 Revision06/2017 BE-XXMS USER MANUAL...
  • Page 12 If the floor apron chain is not moving, the most common cause is improper brake (rear) pawl adjustment. NOTE: By engaging both side drives and turning the beater by hand, you will be able to observe the brake pawl engagement in the sprocket teeth.
  • Page 13 Re-install the safety shield with the three (3) nuts to hold it in place. Re-install the wheel and torque the wheel bolts to 60 ft. lbs. Remove the safety blocking. Figure 3D - Beater Drive Chain Installed in the Proper Position Farmer-Helper 25 & 27G Revision06/2017 BE-XXMS USER MANUAL...
  • Page 14 APPENDIX A: PARTS REFERENCE The following information is provided for your reference in understanding how the spreader is assembled and how spare parts can be identified and ordered properly. General Spreader Specifications BEMS23 BEMS32 MODEL INCH METRIC INCH METRIC Heaped Capacity 29 cu.ft...
  • Page 15 EXPLODED VIEW & PARTS LIST BE-XXMS USER MANUAL...
  • Page 16 BE-XXMS USER MANUAL Farmer-Helper 25 & 27G Revision06/2017...
  • Page 17 *NOTE: The ENDGATE FRAME must be able to PIVOT for proper operation; DO NOT over-tighten the Grade Block nut (item #21). It is recommended that you just tighten the lock nut, then loosen 1/4 turn for proper movement. Farmer-Helper 25 & 27G...
  • Page 18 Push Arm Shield Assembly 23MS 401275 Lever Pivot Assembly, Left 401289 Handle Grip 27G.401240 Push Arm Shield Assembly 32MS 401373 Tire 5.0-12 25G.00.108 Handle Bar GB/T93-1987 Spring washer 12 25G.00.110 Handle sleeve GB/T5783-2000 Bolt M10x40 GB/T5786-2000 Bolt M12x1.5*25 BE-XXMS USER MANUAL...
  • Page 19 T-Rod Link 32MS 401269 Hitch Assembly 25G.00.011 Dolly Jack Bracket GB/T5782-2000 Bolt M12x80 25G.00.013 Adjustable Hitch 25G.00.002 Dolly Wheel Jack Assembly GB/T62-1988 Wing Nut M6 401095 Front Lid 25G.00.104 Endgate 25G.00.105 Endgate Plate 25G.00.012 Endgate Frame 25G.00.103 Rubber Cushion BE-XXMS USER MANUAL...
  • Page 20 B RA B E R EQ .CO M WGSALES@BRABEREQ.COM PHONE: 604-850-7770 FAX: 604-850-7774 TOLL FREE PHONE: 1-877-588-3311 TOLL FREE FAX: 1-800-665-7334 BE-XXMS USER MANUAL...

This manual is also suitable for:

Agriease be-32ms