Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DTD155SY
Summary of Contents for Makita DTD155SY
- Page 1 INSTRUCTION MANUAL Cordless Impact Driver DTD155 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DTD155 Fastening capacities Machine screw 4 mm - 8 mm Standard bolt 5 mm - 14 mm High tensile bolt 5 mm - 12 mm No load speed Hard impact mode 0 - 3,000 min Soft impact mode 0 - 1,300 min Impacts per minute Hard impact mode... -
Page 3: Ec Declaration Of Conformity
Electrical safety Vibration Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any The vibration total value (tri-axial vector sum) deter- adapter plugs with earthed (grounded) power mined according to EN62841: tools. Unmodified plugs and matching outlets will Work mode: impact tightening of fasteners of the maxi- reduce risk of electric shock. - Page 4 Do not let familiarity gained from frequent use Keep handles and grasping surfaces dry, clean of tools allow you to become complacent and and free from oil and grease. Slippery handles and ignore tool safety principles. A careless action can grasping surfaces do not allow for safe handling and cause severe injury within a fraction of a second.
- Page 5 CAUTION: Only use genuine Makita batteries. MISUSE or failure to follow the safety rules stated Use of non-genuine Makita batteries, or batteries that in this instruction manual may cause serious have been altered, may result in the battery bursting personal injury. causing fires, personal injury and damage. It will...
-
Page 6: Functional Description
Indicating the remaining battery FUNCTIONAL capacity DESCRIPTION Only for battery cartridges with the indicator CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge CAUTION: Always switch off the tool before... -
Page 7: Overheat Protection
Overheat protection Lighting up the front lamp When the tool/battery is overheated, the tool stops automatically. In this situation, let the tool/battery cool CAUTION: Do not look in the light or see the before turning the tool on again. source of light directly. Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery. NOTE: Overheat protection (for battery) will work only with batteries with star marking. ► 1 . - Page 8 Reversing switch action CAUTION: Always check the direction of rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may dam- age the tool. CAUTION: When not operating the tool, always set the reversing switch lever to the neu- tral position.
- Page 9 NOTE: A mode is available only when the tool rotates clockwise. When rotating counterclockwise in A mode, the impact force and speed are the same as hard mode. NOTE: When all lamps on the switch panel go out, the tool is turned off to save the battery power. The impact force grade can be checked by pulling the switch trigger to the extent that the tool does not operate. NOTE: While pulling the switch trigger, the impact force grade cannot be changed. To install the driver bit, pull the sleeve in the direc- ASSEMBLY tion of the arrow and insert the driver bit into the sleeve as far as it will go.
-
Page 10: Installing Hook
Standard bolt Installing hook N•m CAUTION: (kgf•cm) When installing the hook, always secure it with the screw firmly. If not, the hook may come off from the tool and result in the personal (1224) injury. (1020) (816) (612) (408) (204) ► 1 . Groove 2. Hook 3. Screw The hook is convenient for temporarily hanging the tool. 1. Fastening time (second) 2. Fastening torque This can be installed on either side of the tool. -
Page 11: Optional Accessories
CAUTION: These accessories or attachments NOTE: Hold the tool pointed straight at the screw. are recommended for use with your Makita tool NOTE: If the impact force is too strong or you tighten specified in this manual. The use of any other the screw for a time longer than shown in the figures, accessories or attachments might present a risk of the screw or the point of the driver bit may be over- injury to persons. Only use accessory or attachment... - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885520B229 www.makita.com 20190221...