Primera 1-56-729A Fittings Manual

175
205
90
32
25
3
PR4-729A
Anti-ligature Pull Handle
10
102
22.5
36
35
3
Escutcheon Plate
PR4-728TP
Anti-ligature Turn/Pull
Note: The cylinder cut out is made on the external side of the door only and must not go right through the door.
Addition for
PR1 Variant
Turn/Pull
Repair Plate
Model Spindle Length Calculation
46 Door Thickness ÷ 2 + 20mm +3mm
56 Door Thickness + 11mm +3mm
66 Door Thickness ÷ 2 + 20mm +3mm
76 N/A N/A
86 N/A N/A
96 N/A N/A
103
58.5
10
35
15
235
68
16
33
60.5
3 80
25 10
PR6130RBD
Roller Bolt Dead lock
32
58
PR4-58E
Euro Profile Escutcheon
164.75
33.50
90 PR7102-TPSP
Thumb Turn Support Plate
Turn/Pull Screw Length
If Fitting
46 Door Thickness Less 3mm
Turn/Pull
56 Door Thickness Less 3mm
Repair Plate
66 Door Thickness Less 3mm
Screw Length
76 N/A
= Door
86 N/A
Thickness
96 N/A
Note A : Check exact door thickness of each door
Note B : Turn/Pull support plate must not be recessed
deeper than the surface of the door.
63
To adjust Roller Catch
projection turn screw
anti-clockwise to
increase or clockwise
165 to withdraw
(Max adjustment
72
6.5mm – 13mm)
30
7 0
14
M5 Bolt
from the
other side
of the door
PR6130RBD
Roller Bolt
Dead lock
10
Note: If, when fitting the pull handle, the screws make direct contact with the lock-case, please use the shorter (5/8") screws included
48.50
in the fixing pack.
Standard Primera Products are designed for internal applications only. For external applications products plated to "Service Condition 5"
should be used.
25°
A: This Turn/Pull is equipped with a screw to adjust the projection of the
spindle if required (most likely if the spindle is cut too short in error) see
drawing A
B: When cutting the spindle to the required length, please make sure that
the material is cut from the end marked B as illustrated. The 3 slots at
the opposite end of the spindle C are an important safety feature and
designed to sheer at 50NM to protect the lock and ensure clinical staff
maintain control of the lock at all times. The O-ring in the first slot will
also assist in the retention of the spindle in the nozzle of the Turn/Pull
during normal use.
B
Adjust length of spindle by cutting with a
hacksaw at this end. It is important that
the end of the spindle is cut square.


Important Note: products are protected by Intellectual Property Rights including UK and Community Unregistered Design Rights, UK and Community Registered Designs and UK Patents and Patent Applications.
Primera Limited, Unit 8 Bankfield House, 250 Bristol Avenue, Blackpool, FY2 0JF
t 0330 058 0988
1-56-729A
Anti-Ligature Indicator Lockset
SOP104 Revision (2)
9 0
1" Screws
PR4-729A
Anti-ligature
PR7102-TPSP
7 0
Pull Handle
Thumb Turn
Support Plate
1" Screws
⁵ / ⁸" Screws
⁵ / ⁸"
Machine
Screws
⁵ / ⁸" Screws
PR4-58E
Euro Profile Escutcheon
Important Spindle & Turn/Pull Information
Adjust the spindle projection screw
by inserting screwdriver through
the door/lockcase.
There must be at least I sheer
point between the end of the
Turn/Pull nozzle & the lockcase.
Lockcase
C
O-Ring
Sheer Points

Do Not Cut Here
For further details please contact Safehinge Primera Limited.
e sales@safehingeprimera.com w www.safehingeprimera.com
Description
Unified Roller Bolt Deadlock 103x235
Spindle Universal 44mm-63mm with O-Ring
Thumb Turn/Pull complete
729 Pull Handle
Escutcheon 58mm Euro
729, 90 x 205mm Radius plate
Indicator plate 90 x 165mm Radius
3 x 33.50 X 79mm Thumb turn support plate
Fixings Included
Note: Unless ordered seperatley the cylinder
is not included in this kit.
A
Door
Lockcase
The spindle must
engage in the socket
by at least 7mm