Primera 1-46-729C Fittings Manual

175
282
22.5
36
90
32
25
3
PR4-729A
Anti-ligature Pull Handle
79
25
PR7101-TPSP
Turn/Pull Support Plate
10
32
48.50
58
25°
PR4-58E
Euro Profile Escutcheon
Note: The cylinder cut out is made on the external side of the door only and must not go right through the door.
Addition for
PR1 Variant
Turn/Pull
Repair Plate
Model Spindle Length Calculation
46 Door Thickness ÷ 2 + 20mm +3mm
56 Door Thickness + 11mm +3mm
66 Door Thickness ÷ 2 + 20mm +3mm
76 N/A N/A
86 N/A N/A
96 N/A N/A
103
58.5
10
63
15
35
68
235
16
72
165
33
30
60.5
3 80
25 10 14
PR6130RBD
Roller Bolt Dead lock
102
35
3
PR4-728TP
Anti-ligature Turn/Pull
Turn/Pull Screw Length
If Fitting
46 Door Thickness Less 3mm
Turn/Pull
56 Door Thickness Less 3mm
Repair Plate
Screw Length
66 Door Thickness Less 3mm
= Door
76 N/A Thickness
86 N/A
96 N/A
Note A : Check exact door thickness of each door
Note B : Turn/Pull support plate must not be recessed
deeper than the surface of the door.
Anti-Ligature Bedroom Lockset
To adjust Roller Catch projection turn
screw
anti-clockwise to
increase or clockwise
to withdraw
(Max adjustment
6.5mm – 13mm)
PR4-728-TP
Anti-ligature
Turn/Pull
7 0
7 0
M5 Bolt
from the
other side
PR7101-TPSP
of the door
Thumb Turn
Support Plate
PR6130RBD
Roller Bolt
Dead lock
Euro Profile
Escutcheon
Note: If, when fitting the pull handle, the screws make direct contact with the lock-case, please use the shorter (5/8") screws
included in the fixing pack.
Standard Primera Products are designed for internal applications only. For external applications products plated to "Service
Condition 5" should be used.
Important Spindle & Turn/Pull Information
A: This Turn/Pull is equipped with a screw to adjust the projection of the
spindle if required (most likely if the spindle is cut too short in error) see
drawing A
B: When cutting the spindle to the required length, please make sure that
the material is cut from the end marked B as illustrated. The 3 slots at
the opposite end of the spindle C are an important safety feature and
designed to sheer at 50NM to protect the lock and ensure clinical staff
maintain control of the lock at all times. The O-ring in the first slot will
also assist in the retention of the spindle in the nozzle of the Turn/Pull
during normal use.
There must be at least I sheer
point between the end of the
Turn/Pull nozzle & the lockcase.
Lockcase
B C
Adjust length of spindle by cutting with a
hacksaw at this end. It is important that
the end of the spindle is cut square.
 Sheer Points


Do Not Cut Here
Important Note: products are protected by Intellectual Property Rights including UK and Community Unregistered Design Rights, UK and Community Registered Designs and UK Patents and Patent Applications.
For further details please contact Safehinge Primera Limited.
Primera Limited, Unit 8 Bankfield House, 250 Bristol Avenue, Blackpool, FY2 0JF
t 0330 058 0988 e sales@safehingeprimera.com
1-46-729C
SOP137 Revision (2)
9 0
Description
Roller Bolt Deadlock 103x235
Spindle Universal 44mm-63mm With O-ring
PR⁴-⁷2⁹
Turn/Pull complete
Anti-ligature
Pull Handle
729 Pull handle
Escutcheon 58mm Euro
⁵/⁸"
729, 90x282 Radius Back plate
Machine
Screws
3x25x79mm Turn/Pull support plate
PR⁴-⁵⁸E
Fixings Included
Note: Unless ordered seperatley the
cylinder is not included in this kit.
PR⁴-⁵⁸E
Euro Profile
Escutcheon
Adjust the spindle projection screw
by inserting screwdriver through
A
the door/lockcase.
Door
Lockcase
O-Ring
w www.safehingeprimera.com
The spindle must
engage in the socket
by at least 7mm