Summary of Contents for HIKVISION DS-K3B411SX Series
Page 1
DS-K3B411SX Series Swing Barrier Quick Start Guide...
Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method;...
Page 4
DS-K3B411SX Series Swing Barrier Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 5
DS-K3B411SX Series Swing Barrier Quick Start Guide under the EMC Directive 2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
Page 6
DS-K3B411SX Series Swing Barrier Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death.
Page 7
DS-K3B411SX Series Swing Barrier Quick Start Guide Do not ingest battery, Chemical Burn Hazard. ● This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Page 8
DS-K3B411SX Series Swing Barrier Quick Start Guide Please keep all wrappers after unpack them for future use. In case of any failure occurred, you ● need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
Page 9
DS-K3B411SX Series Swing Barrier Quick Start Guide Available Models Product Name Model Type Example Description Swing Barrier DS-K3B411SX-L DS-K3B411SX-L/M Left Pedestal DS-K3B411SX-M DS-K3B411SX-M/M Middle Pedestal DS-K3B411SX-M/M DS-K3B411SX-R DS-K3B411SX-R/M Right Pedestal DS-K3B411SX-R/M 868 DS-K3B411SX-LS DS-K3B411SX-LS/M Left Pedestal (No Barrier) DS-K3B411SX-MS DS-K3B411SX-MS/M...
DS-K3B411SX Series Swing Barrier Quick Start Guide Chapter 1 Overview 1.1 Introduction Figure 1-1 Appearance The swing barrier is designed to detect unauthorized entrance or exit. By adopting the swing barrier integratedly with the access control system, personnel should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc.
Page 13
DS-K3B411SX Series Swing Barrier Quick Start Guide Barrier is in open status when powered down; If the device is installed with supercapacitor, the ● barrier remains open when powered down Fire alarm passing ● When the fire alarm is triggered, the barrier will be open automatically for emergency...
DS-K3B411SX Series Swing Barrier Quick Start Guide Chapter 2 System Wiring The preparation before installation and general wiring. Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals.
Page 15
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 2-2 System Wiring Diagram (General Wiring) Note The supplied interconnecting cable length is 3.75 m. If you need a longer one, you can buy a ● new accessory. The suggested inner diameter of the low voltage conduit is larger than 30 mm.
Page 16
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 2-3 Wire Face Recognition Terminal Note The face recognition terminal installed on the left pedestal will gain power from the sub ● switch, which should connect to high voltage. The suggested inner diameter of the low voltage conduit is larger than 30 mm.
DS-K3B411SX Series Swing Barrier Quick Start Guide Chapter 3 Installation 3.1 Disassemble Pedestals Before installation, you should use the key to open the pedestals. View the pictures below to find the lock holes. Figure 3-1 Lock Holes 3.2 Install Pedestals...
Page 18
DS-K3B411SX Series Swing Barrier Quick Start Guide Steps Note The device should be installed on the concrete surface or other non-flammable surfaces. ● In order to prevent stainless steel from rusting due to dirt during the construction process, it is ●...
Page 19
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 3-3 Installation Distance (With Face Recognition Terminal) The dimension is as follows. Figure 3-4 Double-Barrier Dimension...
Page 20
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 3-5 Single-Barrier Dimension 1. Prepare for the installation tools, check the components, and prepare for the installation base. 2. Drill holes on the ground according to the installation holes on the pedestals and insert the expansion sleeves.
DS-K3B411SX Series Swing Barrier Quick Start Guide Chapter 4 General Wiring 4.1 Components Introduction By default, basic components of the turnstile are connected well. The pedestals can communicate by wiring the interconnecting cables. And the turnstile supports wiring the AC electric supply for the whole system's power supply.
DS-K3B411SX Series Swing Barrier Quick Start Guide Note The reinstalled supercapacitor needs to be powered on for at least 3 minutes before it can work normally. The picture displayed below describes the IR adapter and the IR sending/receiving board and their corresponding number on the pedestal.
DS-K3B411SX Series Swing Barrier Quick Start Guide Note The cable bare part should be no more than 8 mm. It is suggested that you can immerse the ● bare part into the liquid tin. If possible, wear an insulation cap at the end of the bare cable.
Page 25
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-3 Cable Hole of Interconnecting Cable Follow the instructions below to connect the interconnecting cable.
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-4 Connect Interconnecting Cable 4.3.1 Pull Interconnecting Cable Steps 1. Use the key to unlock the upper lock of the pedestals and remove the top cover.
Page 27
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-5 Dissemble Top Cover 2. Dissemble the card presenting board.
Page 29
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-7 Dissemble Card Reader Module 4. Pull the interconnecting cable out from the bottom up with pull-out tool, and other wiring operations can be performed. Note Interconnecting cable includes a network cable and a power supply cable of 24 V.
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-8 Pull out Interconnecting Cable 4.4 Wire Network Switch (Optional) Connect the network cable and the network switch. Steps 1. Use the key to open the top cover of the pedestal.
Page 31
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-9 Open Top Cover 2. Attach the network switch to the position shown in the figure with adhesive.
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-10 Network Switch Position 3. Lead out the 12 V power supply from the power switch and connect it to the switch power interface. 4. Connect the network cable according to your actual needs.
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-11 Main Control Board Terminal 4.5.2 Sub Control Board Terminal Description The sub lane control board contains power input, BUS interface, interconnecting interface, supercapacitor interface, IR interface, barrier position control board interface and motor drive interface.
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.3 BUS Terminal Description You can connect the lane controller light board, fan, TAMPER, lane control board, card reader, face recognition terminal, QR code scanner, etc. via the BUS terminal. Note Part of the wiring has been completed at the factory, please connect according to actual needs.
Page 35
DS-K3B411SX Series Swing Barrier Quick Start Guide Terminal Name Description TAMPER Connects TAMPER Lane Controller Board Connect main lane controller board Port 5 Red 12 V: connects 12 VDC power supply terminal Yellow 485E/232E+: card reader RS-485E+/RS-232E+ access Note terminal...
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.4 Access Control Board Terminal Description Access control board is mainly used for authority identification in places with high security levels such as public security or judicial place, external device accessing, and communication with the upper platform and lane controller.
Page 37
DS-K3B411SX Series Swing Barrier Quick Start Guide Access Control Board Terminal Description represents the passage entrance, and 3 represents the passage exit. UART 1 in the main control board corresponds to the entrance card reader, and UART 5 in the main...
Page 38
DS-K3B411SX Series Swing Barrier Quick Start Guide Access Control Board Terminal Description 4, and the guest user swipes the card on the card reader This is the ● RS-485 interface, which cannot be switched by dialing. If you have to ●...
Page 39
DS-K3B411SX Series Swing Barrier Quick Start Guide Access Control Board Terminal Description RS-232 Interface Grounding This is the ● RS-232 RS-232 G- Connect to RS-232G- interface, RS-232 G+ Connect to Card Reader RS-232G+ which cannot be switched Grounding by dialing.
Page 40
DS-K3B411SX Series Swing Barrier Quick Start Guide Access Control Board Terminal Description pipe and connects with the QR code on the left. Power Input +24 V 24 VDC Power Input Grounding Event Input Event Alarm Input 1 The event alarm input...
Page 41
DS-K3B411SX Series Swing Barrier Quick Start Guide Access Control Board Terminal Description entrance, and D2 controls the door opening for ordinary exit. Door 2 Relay Output (Dry Contact) If necessary, the door lock relay can be used to control the third-party barrier switch.
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.5 Access Control Board UART Description You can set the device mode, switch the communication mode of the corresponding UART, and initialize the device through the DIP on the access control board. The DIP switch of the access control board is shown in the figure below: Note The diagram is for reference only.
Page 43
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 4-15 UART No. Description The corresponding functions of different DIP Switch are described as follows: Device Mode UART No. Function Binary Value DIP A 1 to 2: Work Normal Mode Mode Test Mode...
Page 45
DS-K3B411SX Series Swing Barrier Quick Start Guide Device Mode UART No. Function Binary Value Prohibit Entrance and Controlled Exit Prohibit Entrance and Free Exit DIP B 1 to 3 UART 5 ON: UART 5 is RS- 232E Interface 4 to 6...
Page 46
DS-K3B411SX Series Swing Barrier Quick Start Guide Note For proper communication between turnstile and peripherals, DIP Switch No. 1 to 3, 4 to 6, 7, and 8 of DIP B, DIP C, DIP D, and DIP E cannot be turned ON at the same time.
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.6 RS-485 Wiring Note The RS-485 interfaces are for connecting ID card reader, IC card reader, card reader, card recycler, ● text screen, and face recognition terminal. Take the wiring of RS-485 card reader as an example.
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.7 RS-232 Wiring Note Access control board of pedestal can connect QR code scanner, card recycler, and face ● recognition terminal via RS-232 interface. For details about text screen, see Configuring Screen Parameters in User Manual of iVMS-4200 ●...
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.8 Barrier Control Wiring By default, the barrier has connected with the access control board. The lane control board can control the barrier status. If possible, the device can connect with a third party lane control board to control the third party barriers.
DS-K3B411SX Series Swing Barrier Quick Start Guide 4.5.9 Alarm Output Wiring Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) .
DS-K3B411SX Series Swing Barrier Quick Start Guide Chapter 5 Device Settings After installation and wiring completed, the turnstile will learn the open and closed position automatically. After the learning, the turnstile is in the normal mode. You can also set the turnstile to test mode,...
DS-K3B411SX Series Swing Barrier Quick Start Guide By default, the keyfob is in one-to-one mode. The keyfob's DIP switch is towards 1 (OFF). The keyfob can control only one turnstile. One-to-Many Mode The keyfob's DIP switch is ON. In this mode, the keyfob can control multiple turnstiles.
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 5-1 Initialization Jumper Cap 2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep. 3. When the beep stopped, set the No.8 switch to the OFF side, and reboot the turnstile to take effect.
Page 54
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 5-2 Jumper Cap Location (Barrier Control Relay Output Mode) The jumper cap position of barrier opening (NO) is as below: Figure 5-3 Barrier Opening (NO) The jumper cap position of barrier closing (NC) is as below:...
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 5-4 Barrier Closing (NC) Note The default status is NC. 5.3.2 Alarm Relay Output Mode (NO/NC) The jumper cap of the alarm relay on the access control board is as below:...
Page 56
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 5-5 Jumper Cap Location (Alarm Relay Output Mode) The jumper cap position of alarm opening (NO) is as below: Figure 5-6 Alarm Opening (NO) The jumper cap position of alarm closing (NC) is as below:...
Page 57
DS-K3B411SX Series Swing Barrier Quick Start Guide Figure 5-7 Alarm Closing (NC) Note The default status is NO.
Get the SADP software from the supplied disk or the official website http:// ● www.hikvision.com/en/ , and install the SADP according to the prompts. The device and the PC that runs the SADP tool should be within the same subnet.
DS-K3B411SX Series Swing Barrier Quick Start Guide Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP.
Page 60
DS-K3B411SX Series Swing Barrier Quick Start Guide Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
DS-K3B411SX Series Swing Barrier Quick Start Guide Appendix A. DIP Switch Description The DIP switch is on the main lane control board. The left side to the right side is from the low bit to the high bit. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12.
DS-K3B411SX Series Swing Barrier Quick Start Guide Appendix B. Event and Alarm Type Event Alarm Type Tailgating Visual and Audible Reverse Passing Visual and Audible Force Accessing None Climb over Barrier Visual and Audible Overstay Visual and Audible Passing Timeout...
DS-K3B411SX Series Swing Barrier Quick Start Guide Appendix C. Table of Audio Index Related Content Index Content Authenticated. Card No. does not exist. Card No. and fingerprint mismatch. Climbing over the barrier. Reverse passing. Passing timeout. Intrusion. Force accessing. Tailgating.
DS-K3B411SX Series Swing Barrier Quick Start Guide Appendix D. Error Code Description The swing barrier will display the error code on the seven-segment display if error occurred. Refer to the table below to find the description of each number. Error Reason...
Page 65
DS-K3B411SX Series Swing Barrier Quick Start Guide Error Reason Code Error Reason Code The Second IR Beam on Lower Lower IR Board 7 Offline IR Board Triggered The Third IR Beam on Lower IR Lower IR Board 8 Offline Board Triggered...
Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all commonly used serial ports commands for all Hikvision access control and video intercom devices. Figure E-2 Device Command...