Operation - Toshiba MMD-UP0961HFP-E1 Owner's Manual

■
Indicators
All icons on the display are shown for this explanation. Operations are not accepted when "SETTING" is fl ashing.
10
9
8
1
Operation mode indicator
Indicates the operation mode selected.
2
Central control indicator
Displayed when the air conditioner is controlled
centrally and used with central control devices
such as the central remote controller.
If the use of the remote controller is prohibited by
the central control, blinks when the ON/OFF,
MODE, or TEMP. button on the remote controller
is pushed, and the buttons do not function.
(Settings that can be confi gured on the remote
controller differ depending on the mode of the
central control. For details, read the Owner's
Manual of the central remote controller.)
3
Setting indicator
Indicates that the model is being checked
automatically after a breaker is thrown or some
other occurrence.
4
Service indicator
Displayed while the protective device works or a
check occurs.
5
Test run indicator
Displayed during test run.
15-EN
1
2
3
4 11
5
6
7
6
Temperature setting indicator
The selected set temperature is displayed.
7
Fan speed indicator
Indicates the selected fan speed
Auto
Low
Low +
Med.
Med. +
High
Fix
8
OFF timer indicator
When a trouble occurs, trouble code is displayed.
9
Pre-heat indicator
Displayed when the heating mode is energized or
defrost cycle is initiated.
While this indication is displayed, the indoor fan
stops or operate in fan mode.
10
Operation standby indicator
Indicates that the Super Modular Multi System
cannot cool if a different indoor unit is heating or
cannot heat if one is cooling; and that the Super
Heat Recovery Multi cannot heat or cool because
the outside temperature is outside the operating
range.
11
Notice display
Displayed while notice code occurs.
4

Operation

When you use the air conditioner for the fi rst time or change the settings, follow the procedures below.
From next time, pushing the ON/OFF button starts running of the air conditioner with the chosen settings.
■
Standby
Operations are not accepted when "SETTING" is blinking.
REQUIREMENT
• Keep the power switch turned on during use.
• When you resume using the air conditioner after a long period of disuse, turn on the power switch at least
12 hours before starting running.
• When the power is turned on, it takes about 1 minute before the remote controller becomes operable.
This is not a malfunction.
■
Running operation
Some operation modes are not available depending on the type of indoor unit.
Menu button Setting button
1
ON/OFF button
Push this button to light the operation lamp and
start operations.
When heating
• The heated air comes out after a 3 to 5 minutes
of pre-heating with the indoor fan kept turned
off.
2
Select the operation mode
Push the Menu button several times to select the
operation mode.
• The current operation mode fl ashes.
Each time you push the setting button, the
operation mode and its icon change in the
following order:
Heat Cool Fan
(Cooling only mode will not display: "
" Heat")
• If you do not push any button for 30s, the
operation mode fi nishes.
─ 8 ─
3
Select the fan speed
Push the Menu button several times to select the
fan speed mode.
• The current fan speed indicator fl ashes.
Each time you push the setting button, the fan
speed mode and its indication change in the
following order:
• Five-speed models:
Auto Low Low + Med.
• When cooling and heating operation, "AUTO"
has the same fan speed as "High".
• FIX " " is displayed for models capable of
ON/OFF button
the fan speed setting.
• If you do not push any button for 30s, the fan
speed mode fi nishes.
4
Select the temperature
Push the setting button to adjust the temperature.
• The temperature can be set in steps of 1.0°C.
Super Modular Multi System u series (SMMS-u)
Operating Mode Temperature setting range
Cool 13 to 25°C
Heat 18 to 30°C
Other than Super Modular Multi System u series (SMMS-u)
Operating Mode Temperature setting range
Cool
16 to 27°C
Heat
Auto" and
Med. + High
Factory default
18°C
25°C
Factory default
18°C
25°C
16-EN