Advertisement
Quick Links
4" AMPLIFIED RECESSED CEILING SPEAKERS
8" AMPLIFIED RECESSED CEILING SPEAKERS
INTRODUCTION
These instructions contain the specifications and
guidelines necessary to install, operate and maintain
the Amplified Recessed Ceiling Speakers.
Specifications and installation information for the
mounting rings and backboxes used with these
speakers is also included in this document.
These speakers are for use with any Valcom page
control and are for interior use only.
SPECIFICATIONS
Applications
These Amplified Recessed Ceiling Speakers are used
to provide one-way paging when used with a low
level audio input.
•
Valcom Paging Adapters
•
Electronic Key System Page Ports (interface
adapter may be required)
•
PABX Page Ports (interface adapter may be
required)
•
Stand Alone Systems
•
Existing 70V Paging Systems
•
Background Music Systems
Features
•
Self-contained amplifier and volume control
•
Operates on -24VDC
•
Screw terminals for all connections
•
Grille simulates recessed lighting fixture
•
No visible mounting hardware due to concealed
mounting studs for the speaker and torsion
springs
Nominal Specifications
•
Amplifier Input Impedance
•
Amplifier Input Level
•
Amplifier Output
Technical Manuals Online! - http://www.tech-man.com
100 Ohm nominal
-10dBm nominal
1 watt into 45 Ohm
spkr load
1
firealarmresources.com
Power Requirements
Voltage
Current
Environment
Temperature
Humidity
0 to 85% non-precipitating
Dimensions/Weights
•
V-1011BB - 4" Recessed Ceiling Speaker
w/Backbox
7.8" Dia x 5.0"D (19.81cm Dia. x 12.7cm D)
5.8 lbs. (2.63 kg)
•
V-1011MR - 4" Recessed Ceiling Speaker
w/Mounting Ring
7.8" Dia x 5.0"D (19.81cm Dia. x 12.7cm D)
2.4 lbs. (1.09 kg)
•
V-1012BB - 8" Recessed Ceiling Speaker
w/Backbox
11.75" Dia x 6.0"D
(29.85cm Dia. x 15.24cm D)
6.3 lbs. (2.86 kg)
•
V-1012MR - 8" Recessed Ceiling Speaker
w/Mounting Ring
11.75" Dia x 6.0"D
(29.85cm Dia. x 15.24cm D)
3.3 lbs. (1.50 kg)
VSP-V-1011/V-1012
Issue 5
-24VDC
50mA
0 to 50 degrees C
947019
Advertisement
Related Manuals for Valcom VSP-V-1011
Summary of Contents for Valcom VSP-V-1011
- Page 1 Amplified Recessed Ceiling Speakers. Specifications and installation information for the mounting rings and backboxes used with these speakers is also included in this document. These speakers are for use with any Valcom page control and are for interior use only. SPECIFICATIONS Applications...
-
Page 2: System Design
SYSTEM DESIGN General Table 1 - Number of Speakers per Audio Run Valcom Amplified Recessed Ceiling Speakers may be used to provide one-way paging from any Valcom Wire Run (Ft) 22 AWG 24 AWG one-way or talkback page control. The speakers can also be used to expand existing 70V paging systems. -
Page 3: Mounting Procedure
• Connect one output of the V-1094A to screw through one of the four knockouts on the terminal marked Tip on the Valcom amplified backbox and connect the wires to the speaker as speaker. described in the Installation and Connecting •... - Page 4 Valcom Page Adapter Ring -24V Page -24VDC Amplifier Detail Screw Designations Valcom -24VDC Power Supply FIGURE 1 - TYPICAL CONNECTIONS TO VALCOM PAGE ADAPTER 70 Volt Speakers Inexpensive regular twisted pair telephone V-1094A wire 70 Volt Amp 1/4 watt 8 ohm...
- Page 5 This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be liable for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation, or use of the product.