Advertisement
Quick Links
Easy
Easy
Easy Lock
PROXIMITY LOCK RFID 125 KHZ
FORMAT : UNIQUE - SOKIMAT Q5 - ATMEL T5557
Mod. DRF13PG/B/A
Bolt Lenght - 13 mm
Mod. DRF18PG/B/A
Bolt Lenght - 18 mm
READ THE INSTRUCTIONS CAREFULLY
READ THE INSTRUCTIONS CAREFULLY
BEFORE USE AND KEEP THEM FOR
BEFORE USE AND KEEP THEM FOR
USER'S GUIDE
USER'S GUIDE
MAINTENANCE
MAINTENANCE
INSTALLATION GUIDE
INSTALLATION GUIDE
Lock
Lock
!
FUTURE REFERENCE
FUTURE REFERENCE
RFID
RFID
125 Khz
ENT
STATUS
ENT
STATUS
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
0
0
PAGE 2
PAGE 4
PAGE 8
Advertisement
Related Manuals for Digitron DRF13PG/B/A
Summary of Contents for Digitron DRF13PG/B/A
- Page 1 125 Khz PROXIMITY LOCK RFID 125 KHZ FORMAT : UNIQUE - SOKIMAT Q5 - ATMEL T5557 STATUS STATUS Mod. DRF13PG/B/A Bolt Lenght - 13 mm Mod. DRF18PG/B/A Bolt Lenght - 18 mm READ THE INSTRUCTIONS CAREFULLY READ THE INSTRUCTIONS CAREFULLY...
- Page 2 USER’S GUIDE USER’S GUIDE STATUS Sensore SHARED USE : The lock closes with any compatible TAG ( Card or Wristband ) and it will open only with the same TAG used to close CLOSING Lean the TAG ( Card or Wristband ) to the centre of the sensor. The LED will shortly flash 1 time every 2 seconds to indicate that the lock is closed OPENING...
-
Page 3: Timer Setting
PERSONAL USE It is possible program the lock so that it works with a specific personal TAG ( Card or Wristband ). With the lock “open” lean the special READ FIXED card to the center of the sensor and remove the card only when the the LED turns “ON”. Within 5 seconds ( before the LED turns “OFF”... -
Page 4: Read Carefully
READ CAREFULLY READ CAREFULLY FEW INSTRUCTIONS AND SOME SUGGESTIONS TO KEEP EFFICIENT THE LOCKS FEW INSTRUCTIONS AND SOME SUGGESTIONS TO KEEP EFFICIENT THE LOCKS CLEANING Clean the lock exclusively with a dump cloth. Avoid soap, solvents, alcohol etc. AVOID TO MAKE ENTER THE WATER IN THE LOCK If the water gets inside the lock in addition to discharge the batteries can permanently damage the lock BATTERIES ( see page 5 ) When the batteries have not enough power to close the lock the led red turn ON and stays ON until the complete... -
Page 5: Replacing The Batteries
REPLACING THE BATTERIES REPLACING THE BATTERIES THE LOCK DOES NOT WORK AND THE RED LED IS “ON” STATUS THE LOCK IS COMPLETELY INACTIVE BATTERIES DISCHARGED BATTERIES DISCHARGED ALKALINE BATTERIES ( 1,5 V - AAA ) USE ONLY ALKALINE BATTERIES DO NOT USE RECHARGEABLE BATTERIES IT IS RECOMMENDED TO REPLACE THE BATTERIES WITHIN 2 YEARS FROM THEIR INSTALLATION PAG. - Page 6 OBSTACLE OBSTACLE PAY ATTENTION IF DURING THE CLOSING PHASE THE BOLT HITS AGAINST THE STOP-BOLT AND IT DOES NOT CLOSE ( SEE FIGURE 3 AND 4 ) AFTER 3 SECONDS THE BOLT COME BACK IN THE POSITION “OPEN”.. THE REPETITION OF THE PROBLEM COULD DAMAGE THE INTERNAL MECHANISM.. IF THE LOCK CLOSES BUT THE BOLT FORCES HORIZONTALLY AGAINST THE STOP-BOLT ( SEE FIGURE 2 ) THE CONSUMPTION OF BATTERIES DRASTICALLY INCREASES.
- Page 7 USO OF EXTERNAL POWER SUPPLY ( PFAESEL02 ) USO OF EXTERNAL POWER SUPPLY ( PFAESEL02 ) EMERGENCY OPEN Remove the protection glass and the label as shown in the picture. With the external power supply commutator on “ ON “ position connect the two metal point in the proper holes paying attention to the polarity.
- Page 8 INSTALLATION GUIDE INSTALLATION GUIDE Fig. Make on the door n.5 holes of 9 mm diameter. To determine the horizontal positions of the holes refer to the picture 8.1 and 8.2 and make sure that the bolt of the lock correctly acts while closing and opening N.
- Page 9 Fig. After having removed the cover of the lock slip the cables through the proper hole placed on the backm of the lock and insert its in the connectors as shown in the picture. Fig. Bend the cables as shown in the picture in such a way to set the wires between the lock and the door.
- Page 10 Fix the lock and the sensor to Fig. DOOR the door with n.4 screws for plastic materials, cylindric head, 4 mm diameter, 20 mm lenght SENSOR LOCK ( L ) ( max ) 3 mm (min) Fig. 6 mm (max) The lenght of the screws ( L ) may change according to the thickness of the door and the further spacer* used.
- Page 11 USE OF SPACER 4 mm Pic. The spacer is an optional accessory to be used when you want to leave the body of the lock from the door. Pic. DOOR SPACER LOCK SENSOR More spacers can be used for the door with reduced thickness.
- Page 12 INSTALLATION OF THE NUMBER Pic. Insert the adhesive label* in the proper space. * The use of AVERY L 6008 polyesther 25,4 x 10 mm labels for laser white and black printers is recommended. Pic. Insert in the slot at the top of the protection glass.
- Page 13 QUOTE FOR LOCK FIXING Model DRF18PG/A/B = 18 mm Pic. SCALA 1: 1 BOLT Left opening door N.5 Holes ( door ) diameter 9 mm Right opening door BOLT 37.5 37.5 (Min.) Pic. 3 mm PLEASE NOTE THAT THE NON OBSERVANCE OF THE RULES ABOVE DESCRIBED FOR A CORRECT INSTALLATION WILL AUTOMATICALLY VOID EVERY KIND OF WARRANTY OF THE PRODUCT...
- Page 14 DIMENSIONS LOCK n.4 fori Model DRF18PG/A/B = 18 mm SENSOR STATUS...