Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PCSS 15-20V
Summary of Contents for Trotec PCSS 15-20V
- Page 1 PCSS 10-20V ORIGINAL INSTRUCTIONS CORDLESS PORTABLE CIRCULAR...
-
Page 2: Table Of Contents
PCSS 10-20V Warning of sharp object This symbol indicates dangers to the life and health of persons due to pointed objects. https://hub.trotec.com/?id=41422 Warning of hand injuries This symbol indicates dangers to the health of persons due to hand injuries. Warning... -
Page 3: Safety
General Power Tool Safety Warnings – Personal Safety safety General Power Tool Safety Warnings • Stay alert, watch what you are doing and use common Warning sense when operating a power tool. Do not use a Read all safety warnings, instructions, illustrations power tool while you are tired or under the influence of and specifications provided with this power tool. - Page 4 • Disconnect the plug from the power source and/or • Do not use a battery pack or tool that is damaged or remove the battery pack, if detachable, from the power modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk tool before making any adjustments, changing of injury.
- Page 5 Safety warnings for all saws • Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position Sawing methods your body to either side of the blade, but not in line • DANGER: Keep hands away from cutting area and the with the blade.
- Page 6 Be aware of the data. time it takes for the blade to stop after switch is released. We recommend using the power tool with original Trotec Additional safety warnings for portable circular saws accessories.
- Page 7 Warning of electrical voltage Observe the correct disposal of the battery! This symbol indicates the following: Before any work on the device, remove the mains plug Ensure that the battery is disposed of correctly and from the mains socket and the battery from the device! Hold onto the mains plug while pulling the power cable never dispose of it in waste water or public waters.
-
Page 8: Information About The Device
Warning Behaviour in the event of an emergency / emergency stop function Toxic dusts! The harmful / toxic dusts produced during operation Emergency stop: pose of risk to the health of the operator and persons Removing the battery results in the function of the device in the vicinity. - Page 9 Device depiction Designation Spindle lock Laser button Additional handle Laser aperture Wing screw for cutting angle Rip fence holder Chip ejector Handle Battery holder Quick charger Red battery LED (battery charging) Battery 3-stage battery level indication Release button Green battery LED (quick charger ready for operation) Locking screw for the cutting depth Wing screw for rip fence Pendulum guard...
- Page 10 Scope of delivery Parameter Value • 1 x Cordless portable circular saw PCSS 10-20V Vibration information according to EN 62841 • 1 x Rechargeable battery Total vibration emission value (for sawing wood): • 1 x Quick charger Vibration emission value 1.879 m/s² Main handle a •...
-
Page 11: Transport And Storage
Storage Transport and storage Before storing the device, observe the following: Note • Switch off the device. If you store or transport the device improperly, the • Hold onto the mains plug while pulling the power cable of device may be damaged. the charger out of the mains socket. -
Page 12: Start-Up
2. Insert the mains plug of the quick charger (10) into a Start-up properly fused mains socket. ð The red battery LED (11) lights up. Unpacking the device ð Charging requires approx. one hour. • Take the transport case out of the packaging. 3. - Page 13 Removing the battery Adjusting the cutting depth 1. Detach the battery (12) from the device by pressing and In the 0° position, the cutting depth can be set in the range from holding the unlocking button (14, I.) and pulling the battery 0 mm to 48 mm.
- Page 14 4. Note that the cutting line runs along between the notches Adjusting the cutting angle on the base plate marked 0 and 45, depending on the You can adjust the cutting angle in the range from 0° to 45°. cutting angle setting. In the example below, the cutting angle is set to 45°: Info For mitre cuts, the cutting depth is smaller than the...
- Page 15 As standard, the device is supplied with a saw blade with 8. Remove the clamping screw (20) as well as the clamping 18 teeth (suited for wood and plastic). The saw blade is flange (19). preassembled. 9. Remove any material residues from the device, in particular from the lower guard.
- Page 16 14. Insert the new saw blade (27). When doing so, make sure 16. Refit the clamping flange (19) on the saw blade clamp (33). that the direction of the arrow on the saw blade In doing so, make sure to insert the clamping flange as corresponds to that of the arrow on the device.
- Page 17 18. Press and hold the spindle lock (1). Mounting and adjusting the rip fence 1. Loosen the wing screw (17) and insert the rip fence (26) into the rip fence holder (6). 19. Tighten the clamping screw (20) by means of the Allen wrench (28). 2. Set the desired distance from the cutting line to the edge 20.
-
Page 18: Operation
Checking the pendulum guard Operation The pendulum guard is an important safety device of the power Tips and notes on handling the circular saw tool. It must function properly; otherwise the device must not be used. General information: • Keep the venting slots clear to prevent the motor from Observe the following information: overheating. - Page 19 Sawing wood: Switching the laser on and off • Before sawing wood, chipboards, building materials etc., If required, you can switch on the laser to mark the cutting line. check the above for foreign objects, e.g. nails, screws or Warning of laser radiation similar.
- Page 20 8. Wait a moment until the motor has reached full speed. Switching the device on and off 9. Move the device closer to the workpiece. Wear your personal protective equipment when working with 10. Move the device along the cutting line with a slight forward the device.
-
Page 21: Available Accessories
• Check the quick charger for damages. Should the quick • If required, allow the device to cool down. charger be damaged, stop using it. Contact the Trotec customer service. • Remove the battery from the device (see Start-up chapter). -
Page 22: Maintenance
The saw blade is loose: opened must only be carried out by authorised • Check the saw blade for tight fit. specialist companies or by Trotec. • Check the flange and flange nut for tight fit. Do not use Notes on maintenance... -
Page 23: Disposal
• Non-coated saw blades can be protected against corrosion by applying a thin layer of acid-free oil. Remove any oil We – Trotec GmbH – declare in sole responsibility that the before starting to saw to prevent oil residues from reaching product designated below was developed, constructed and the wood. - Page 24 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...