Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ytc SPTM-5V Series
Summary of Contents for Ytc SPTM-5V Series
- Page 1 Smart Position Transmitter PRODUCT MANUAL SPTM-5V SERIES VERSION 1.01...
-
Page 2: Table Of Contents
3.2 SPTM-5VL Installation …………………………………………………………………………… 3.3 SPTM-5VR Installation ……………………………………………………………………………. 9 4. Connection– Power………….…………………………………………………………………..…… 10 4.1 Safety …………………………………………………………………………………………..…. 10 5. Adjustment …………………………………………………………………………………………….. 11 5.1 Setting Point Switch………………………………………………………………………………. 11 5.2 Adjustment - Calibration………………………………………………………………………….. 11 5.3 Adjustment – Potentiometer …………………………………………………………………….. 11 6. Troubleshooting ……………………………………………………………………………………….. 12 SPTM-5V series... -
Page 3: Introduction
Please ensure the unit is being used and installed within the explosion proof certified environment. SPTM-5V series explosion proof grades are Ex ia IIC T6. Certified ambient temperature is -20’C ~ 60’C. The product should be used in certified... -
Page 4: Product Description
Explosion Proof: Indicates certified explosion proof grade. Input.: Indicates input rotation angle Output: Indicates output signal range Lot No.: Indicates unique lot number ** SPTM-5V series’ KCs certification conforms Ministry of Employment and Labor announcement article No. 2010- SPTM-5V series... -
Page 5: Product Number
Ex ia IIC T6 (KCs) Explosion Proof Operating: -40’C ~ 85’C Explosion Proof: -20’C ~ 60’C Ambient Temp. LCD Operating: -30 ~ 85’C ± 1% F.S. Linearity 0.2% F.S Hysteresis ± 0.2% F.S. Sensitivity Aluminum Diecasting Material 0.6 kg Weight SPTM-5V series... -
Page 6: Parts And Assembly
Parts and Assembly SPTM-5V series... -
Page 7: Dimension - Sptm-5Vl
Dimension – SPTM-5VL Dimension – SPTM-5VR SPTM-5V series... -
Page 8: Installation
6.5mm. The connection pins outer diameter should be less than 6.3mm. 5. Connect supply pressure to the actuator temporarily. Supply enough supply pressure to the actuator in order to position the actuator clamp at 50% of the total valve stroke. SPTM-5V series... -
Page 9: Sptm-5Vr Installation
SPTM-5V should be installed further away from the yoke. SPTM-5VR Installation 1. Please refer to SPTM-5VL installation section for important note for bracket design. 2. There are two types of the lever – standard and NAMUR type. SPTM-5V series... -
Page 10: Connection- Power
600V (complying to the conductor table of NEC Article 310.) The outer diameter of the cable should be between 6.35 ~ 10mm. Use shield wire to protect against electro- magnetic field and noise. Please do not install the cable near high noise equipments, such as high-capacity transformer or motor. SPTM-5V series... -
Page 11: Adjustment
5. Adjustment Setting Point Switch SPTM-5V series can be calibrated in 2 or 5 points setting. a) 2 Point Setting: By setting minimum and maximum points <0% and 100% of valve stroke>, in-b b) 5 Point Setting By setting 5 points <0%, 25%, 50%, 75%, and 100%> the outputs can be set accordingly. -
Page 12: Troubleshooting
A. Please make sure that SPTM-5V’s lever is placed at 50% point. If not, SPTM-5V needs to be re-installed and adjusted to be placed at the 50% point. B. Adjust the potentiometer. Potentiometer’s load resistance is 10KΩ, and it should be ready at the 50% point. SPTM-5V series... - Page 13 Manufacturer: Young Tech Co., Ltd #3022, Hagun-ri, Yangchon-myeon Kimpo-si, Kyeonggi-do, 415-843 South Korea Tel: +82-31-986-8545 Fax: +82-31-986-2683 Email: ytc@ytc.co.kr Copyright © Young Tech Co., Ltd. All Rights Reserved. SPTM-5V series...
Need help?
Do you have a question about the SPTM-5V Series and is the answer not in the manual?
Questions and answers