Related Manuals for Ytc SPTM-6V Series
Summary of Contents for Ytc SPTM-6V Series
- Page 1 Young Te ch c o, LTD. www.ytc.co.kr SMART POSITION TRANSMITTER SPTM-6V SERIES USER'S MANUAL Ver 1.00 #662-8 PungMu Dong, Kimpo City, KyeongGi Do, 415-809, KOREA TEL: (82 31) 986 – 8545 FAX: (82 31) 986-2683...
-
Page 2: Table Of Contents
Young Te ch c o, LTD. www.ytc.co.kr Table of Contents Contents Page No. Introduction Manufacturer Warranty Product Description Label Description Suffix Symbol Specification Parts and Assembly Dimension Operation Logic Installation SPTM-5VL SPTM-5VR Connection – Power Adjustment – Potentiometer Adjustment – Setting Points Adjustment –... -
Page 3: Introduction
Introduction Thank you for choosing YTC product. Each product is fully inspected after the production to offer you the highest quality. In order to fully utilize the product, we strongly recommend users to read the manual carefully and fully understood. -
Page 4: Product Description
Young Te ch c o, LTD. www.ytc.co.kr Product Description SPTM-6V series mechanically changes the position of the stem installed on the valve or similar device and transmits DC 4~20mA of electric signal. Label Description Model: Indicates model number. Input: Indicates input angle range. -
Page 5: Parts And Assembly
Young Te ch c o, LTD. www.ytc.co.kr Item/Model SPTM-6VL SPTM-6VR Input Type 2Wire 0~30 ﾟ 0~90 ﾟ Input Signal Output Signal 4~20mA Max.600 Ω / 28V DC Load Resistance Supply Voltage 9~28V DC Noise Range 50mV p.p Conduit PF 1/2 (G 1/2) -
Page 6: Dimension
Young Te ch c o, LTD. www.ytc.co.kr Dimension #662-8 PungMu Dong, Kimpo City, KyeongGi Do, 415-809, KOREA TEL: (82 31) 986 – 8545 FAX: (82 31) 986-2683... -
Page 7: Operation Logic
② Attach SPTM-6VL to the bracket, which was made in earlier step, by using bolts. <Fig 2>. Please refer to the backside of the product for size of the bolts. The standard size of bolt is M8 x 1.25P, and other bolt sizes are available. Please contact YTC sales department. - Page 8 Young Te ch c o, LTD. www.ytc.co.kr <Fig 2> <Fig 3> ③ Attach SPTM-6VL (with bracket) to the actuator yoke – DO NOT TIGHTEN COMPLETELY. ④ Connect SPTM-6VL feedback lever to the actuator clamp. The gap on the feedback lever is 6.5mm.
-
Page 9: Sptm-5Vr
Young Te ch c o, LTD. www.ytc.co.kr SPTM-6VR Installation SPTM-6VR should be used for rotary motion valve, that is ball valve, butterfly valve using rack and pinion, scotch yoke or complex type actuator, which its stem rotates 90 degrees. ① Before installing SPTM-6VR, please set the actuator as default position. For single acting type (spring return type), the actuator will automatically default itself when the air pressure shuts down. -
Page 10: Connection - Power
Young Te ch c o, LTD. www.ytc.co.kr Connection - Power Note Before connecting terminal, please make sure that power is off completely. SPTM-6V must be grounded. Please use twisted cable with conductor section area 1.25 ㎟ and that is suitable for 600V ... -
Page 11: Adjustment - Potentiometer
Young Te ch c o, LTD. www.ytc.co.kr Adjustment – Potentiometer Potentiometer is designed to output 12mA signal when the feedback lever is at 50% position. In case of dislocation of the potentiometer, please follow below procedure to re-set the potentiometer. -
Page 12: Adjustment - Setting Points
Young Te ch c o, LTD. www.ytc.co.kr Adjustment – Setting Points SPTM-6V can be calibrated either by following options. 1. 2 point setting By setting minimum and maximum points <0% and 100%>, between outputs are calculated and calibrated automatically. 2. 5 point setting By setting 5 points <0%, 25%, 50%, 75%, and 100%>, the outputs can be set... -
Page 13: Troubleshooting
Young Te ch c o, LTD. www.ytc.co.kr Troubleshooting 1. SPTM-6V shows no output signal. A. Check actual input signal to SPTM-6V. B. Check power connection and + / - poles. 2. Input signal value to positioner and output signal value from SPTM-6V differs dramatically. - Page 14 Fax: 82-31-986-2683 Web: www.ytc.co.kr This manual can be changed or revised without any prior notice. For latest version, please contact YTC website. Issued: 2009.APR,14 Version 1.00 #662-8 PungMu Dong, Kimpo City, KyeongGi Do, 415-809, KOREA TEL: (82 31) 986 – 8545...