Table of Contents
Advertisement
SAFETY Continued
11. Do not run fi replace insert
• where fl ammable liquids or vapors are used or stored
• under dusty conditions.
12. Do not use this fi replace insert to cook food or burn paper or other
objects.
13. Do not use fi replace insert if any part has been exposed to or under
water. Immediately call a qualifi ed service technician to inspect
fi replace insert and to replace any part of the control system and
any gas control which has been under water.
14. Do not operate fi replace insert if any log is broken. Do not operate
fi replace insert if a log is chipped (dime-sized or larger).
15. Turn fi replace insert off and let cool before servicing. Only a quali-
fi ed service person should service and repair fi replace insert.
16. Operating fi replace insert above elevations of 4,500 feet could
cause pilot outage.
17. To prevent performance problems with propane/LP units, do not
use propane/LP fuel tanks of less than 100 lb. capacity (propane/
LP units only).
18. Provide adequate clearances around air openings.
19. Trim panels and surrounds must not seal ventilation openings in
fi replace.
20. Cutting any sheet metal parts of the solid-fuel burning fi replace in
which the vent-free fi replace insert is to be installed is prohibited.
21. If factory-built fi replace has no gas access hole(s) provided, an
access hole of 1.5" (37.5 mm) diameter or less may be drilled
through the lower sides or bottom of fi rebox in a proper manner.
This access hole must be plugged with noncombustible insulation
after the gas supply line has been installed.
22. Refractory, glass doors, screen rails, screen mesh and solid fuel
log grates (if applicable) can be removed from the fi replace before
installing the unvented fi replace insert.
23. Smoke shelves, shields and baffl es may be removed if attached
by mechanical fasteners.
4
Install and use fi replace with care. Follow all local codes. In the
absence of local codes, use the latest edition of The National Fuel
American National Standards Institute, Inc.
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
These appliances are approved for installation in the US state of Mas-
sachusetts if the following additional requirements are met:
•
Un-vented Room Heaters shall be installed in accordance with
527 CMR 30.
•
Installation and repair must be done by a plumber or gas fi tter
licensed in the Commonwealth of Massachusetts.
•
The fl exible gas line connector used shall not exceed 36 inches
(92 centimeters) in length.
•
The individual manual shut-off must be a T-handle type valve.
•
Unvented appliances may NOT be installed in bedrooms or
bathrooms.
•
A working smoke detector must be installed in the area where
vent-free appliances are installed.
Seller of unvented propane or natural gas-fi red supplemental room
heaters shall provide to each purchaser a copy of 527 CMR 30 upon
sale of the unit.
CAUTION: Do not remove the warning and instruc-
tion labels attached to the heater base assembly.
These markings contain important warranty and safety
information.
1. With utility knife, cut carton all the way around above staples on
bottom tray. Lift carton off of heater. Remove packing.
NOTE: Hood is located in packing on right hand side of heater
front. Lift heater off bottom tray.
2. Locate two screws above top corners of fi replace insert screen.
Remove and discard these screws. Lift fi replace insert screen
up and pull out to remove.
3. Remove protective packaging applied to logs, log base assembly
and fi replace insert.
4. Remove fi replace insert hood from carton insert.
5. Check all items for any shipping damage. If damaged, promptly
inform dealer where you purchased your fi replace insert.
SuperiorFireplaces.us.com
LOCAL CODES
Gas Code ANSI Z223.1/NFPA 54*.
*Available from:
25 West 43rd Street, 4th fl oor
New York, NY 10036
National Fire Protection Association, Inc.
1 Batterymarch Park
Quincy, MA 02169-7471
UNPACKING
127119-01C
Advertisement
Table of Contents
